Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I'm using the UART to talk to a GSM modem. It has hardware flow control and supports a baud rate of 115200. I'm using app_uart_fifo.c, not app_uart.c. I'm using the SoftDevice...
Hi,
Does Nordic Semiconductor provide any resources (codes, macros, documents) for work with IAR or Keil's simulator to fully simulate nRF51822's peripherals?
Thanks...
Hi,
I do:
err_code = ble_bondmngr_bonded_centrals_delete();
APP_ERROR_CHECK(err_code);
till now all is ok.
But when I do:
err_code = ble_bondmngr_whitelist_get...
Hi,
I need to delete all centrals using ble_bondmngr_bonded_centrals_delete ble_bondmngr.c function. It is working but it is not cleaning the whitelist.
So, when I do...
In the example of hid_mouse, ble device will bond master when disconnect event happen.
I try to add this two codes to Implement my idea.
err_code = ble_bondmngr_bonded_masters_store...
I write this code to set my ble device power down,but it causes reboot without any error report.
GPIO_WAKEUP_BUTTON_CONFIG(LEFT_BUTTON_PIN_NO);
GPIO_WAKEUP_BUTTON_CONFIG...
I try to use 51822 to run ANCS sample(ble_app_ancs). It work well and I can get notification source and notification attributes. But I don't see any source code for get App...
Hi
I've a reproducable behavior i'm not able to explain. I'm using the softdevice S110 6.0 on a nRF51822.
The firmware implements some BLE profiles and uses TWI Master...
Is there a way to map external memory (SPI connected) to force the app to start execution from there ?
If not feasable , there is a way to transfer the execution from internal...
I have a 51422 board design and I just got Ant-FS working with our firmware so I can now download data from an external SPI flash to a desktop application.
I want to be...
Hello:
I am using NRF51822 to design somethings. And I want to use interrupt send method instead of polling send method.
NRF51822's UART0 provides TXDRDY interrupt. After...
Hi,
I have tested the nRF Toolbox proximity application using nrf51822 evaluation kit and with nexus4 smartphone it is working fine. Now my question is, is it possible to...
Hi
I am trying to overcome the problem that I have confronted, I have no buttons to delete bonds. So instead of deleteing this is what I did.
I modified the bondmanager...
I am developing hid_mouse . When I connect Android once and ubond hid_mouse I must set bluetooth off and on again to connect ble device otherwise it will connect again to...
