Subject: nRF52833 - OpenOCD ST-LINK MEM-AP Access Failure During Flashing
Hello Nordic Support Team,
I am working with an nRF52833 module and trying to flash firmware...
Hi,
1.Can the sQSPI and SPI functions of nRF54L15 operate simultaneously at 32 MHz on the P2 port? 2.Can the sEMMC and SPI of nRF54L15 operate simultaneously at 32 MHz on...
Hi,
I'm designing a battery-powered active RFID timing base station and I'm evaluating the nRF54L10 for it. Patrick from Nordic suggested the nRF54L series over the older...
Only information I can get back for the nPM1304 datasheet from Nordic's website is an html version that's missing all the normal sections you expect in a datasheet. Things...
Enabling CONFIG_USE_SWITCH=y causes usage fault on nRF54L15 with nRF Connect SDK v3.4.0-rc1.
Where it crashes: Context switch on interrupt exit, Zephyr arm-m-switch.c :...
I want to use a UART line to send and receive data to a nrf52840 DK and then have the data sent wirelessly to a separate DK and then print it to a terminal like in the multi_sensor...
Hello,
currently am working on connecting two different modules of BLE, nrf51822 and Rn4871.
The problem am facing is that i am not able to send and receive data between...
Hi,
We are using mesh SDK 5.0 on NRF52840 integrated with PIR and light level sensors for office lighting, it works well.
Now we'd like to check if we can expand the system...
Hi while implementing/testing MTP on Linux Wireshark captured setup requests asking for "Device Qualifier Descriptor" according to section "9.6.2 Device_Qualifier" in the...
Hello,
Can you please provide information for current consumption of the GPS in these modes?
VDD=3.8V
Acquisition time = ? seconds
Acquisition current = ?mA
Tracking...
Dear all,
For our project we want to store information on the device in an additional flash partition. We have created a new flash partition, called factory_settings_partition...
Helo Nordic support team,
I am supporting a client that has designed a product using the NRF9160 with GPS. The product has a small patch antenna mounted on the pcb board...
Hello. I am trying to build an project and I need to use RF module. And I have to Use pic18f45k22 with MikroC. But I couldnot. I have some 18f45k22 codes but dont work I dont...
Hello,
I need to retrieve the IP-Address of the modem, are there any convenient way I can do this?
AT commands maybe?
Appreciate any info on this.
With regards...
Hello
I am having rather odd problem with SWDIO pin shorted to ground. I am using Fanstel BT840x BLE module and I have never seen this issue on my custom board until last...
I see this line for cache enable register in application domain : infocenter.nordicsemi.com/index.jsp
NVMC built-in cache not supported (ICACHECNF, IHIT and IMISS registers...
I'm trying to test button less dfu on nrf 52840 dk. i am simply compile that hex ble_app_buttonless_dfu_without_bonds_s140_with_setting_page.h file with soft device s140 or...
I am building the coded bluetooth gateway using nrf52840 and ENC28J60. Integrated between two examples:
https://github.com/nrfconnect/sdk-nrf/tree/master/samples/bluetooth...
Hi to everyone!
I am working (with Keil uVision) on a custom PCB that includes the NRF52832 (MDBT42Q module) and some sensors from MAXIM INTEGRATED. There is a Sensor Hub...
Hello, I was told to make a new ticket after commenting on this ticket .
I am using SDK 14.2, S140 alpha, NRF52840. Segger IDE. I have been developing with this IDE & SDK...
