Subject: nRF52833 - OpenOCD ST-LINK MEM-AP Access Failure During Flashing
Hello Nordic Support Team,
I am working with an nRF52833 module and trying to flash firmware...
Hi,
1.Can the sQSPI and SPI functions of nRF54L15 operate simultaneously at 32 MHz on the P2 port? 2.Can the sEMMC and SPI of nRF54L15 operate simultaneously at 32 MHz on...
Hi,
I'm designing a battery-powered active RFID timing base station and I'm evaluating the nRF54L10 for it. Patrick from Nordic suggested the nRF54L series over the older...
Only information I can get back for the nPM1304 datasheet from Nordic's website is an html version that's missing all the normal sections you expect in a datasheet. Things...
Enabling CONFIG_USE_SWITCH=y causes usage fault on nRF54L15 with nRF Connect SDK v3.4.0-rc1.
Where it crashes: Context switch on interrupt exit, Zephyr arm-m-switch.c :...
I have a custom board based on NRF52811. Salient features:-
Both HF and LF crystals are present on board.
Power supply is 3.3V.
MCU DC-DC is enabled.
I am using...
Hello.
I trying the test for real time transfer a data.
Period is 4 ms and 5000 point data. (Total 20 sec)
The GPIOTE event occurs every 4ms and the processed...
how to unpair our nrf52 device once it's paired with another nrf52 device, currently we need to switch off the device so that we can pair another device.
Hi all,
I have a customer that has requested NRC tap to pair functionality for their device, mostly for convenience. This is fine, but I'd like to know what they're getting...
Hi,
We are running into a weird issue with some our devices when they are in the bootloader.
The bootloader fails with this error in nrf_dfu_validation.c: Invalid protocol...
Hello,
We have a firmware with 2 versions that runs on Baremetal and FreeRTOS on nRF52840 DK. We would like to port this firmware to nRF9160 without Zephyr and continue...
Dears.
when I connect nRF52833 to connect DK board, JLINK is ok .but could not find device from target device selection.
nRFGo studio is the same. what's the reason for...
Hi All,
I am able to perform the OTA DFU from the NRF52840 Dongle using the NRF Connect Bluetooth low energy application and default Nordic firmware.
I would like to...
I have a service with 2 characteristics, TX and RX. On TX the notify is enabled, because TX should send a notification when something changes. I manage to change what is needed...
Hello everyone.
We have a design based on NRF52840, which uses the built in USB peripheral and was fully tested and prototyped using NRF52840-QIAAD0-2031MR. We have now...
Hi There,
I have downloaded the nRFgo studio and nRFgo SDK and other files found here: https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF24-series
...
For the MPSL/timeslot example in NCS 1.5.0, I am trying set up a TIMER0 compare interrupt to take clean-up actions before the timeslot ends, as suggested in here . However...
Describe the bug Attempted to use the samples/bluetooth/hci_usb/ project with CONFIG_BT_EXT_ADV=y CONFIG_BT_EXT_ADV_LEGACY_SUPPORT=y CONFIG_BT_EXT_ADV_MAX_ADV_SET=4 CONFIG_BT_PER_ADV...
Hi, I have the Power Profiler Kit PCA63511 used on top of the dev kit PCA10040. I am trying to measure the power consumption of my custom hardware implementing nrf52832 using...
