I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
How do I configure the chip to operate in radio mode or BLE mode on the same build?
It seems the radio mode example projects use no soft device, but the BLE project I want...
Hi guys,
I am developing the program for Mesh SDK where I will need to use different functionalities from different C files that I defined, into main.c. I have already defined...
so Im tring to use interactive command to output my personal content
same as the device command which out put the device message
but i want to find the function which...
Hi, Iam trying to integrate secure serial DFU over UART with ble_app_uart application. After integrating serial dfu code My application hardfaults at sd_softdevice_enable...
I'm trying the first steps of the initial tutorial with the nRF5340 kit, from here:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_gsg_ncs%2FUG%2Fgsg%2Ffirst_test...
ERROR: JLinkARM DLL reported an error. Try again. If error condition ERROR: persists, run the same command again with argument --log, contact Nordic ERROR: Semiconductor and...
Dear sir,
Need to print RSSI value , What should i use SCAN_START() OR ADVERTISING_START () , WHICH ONE SHOULD I USE ??? AND WHAT IS THE PROPER EXAMPLE ON NRFSDK
...
HI
I'm in the process of evaluating nRF5340 but am new to Nordic chips and development environment. Im running Windows 10 and I installed nRF Connect 3.6.1 and installed...
Dear All,
I would like to know information about QDID for nRF5 SDK for Mesh v4.2.0, we are developing costumed equipment using NRF52833 and we need to start the process...
Dear Nordic support team.
Our product nearly complete Rnd stage.
We face only one thing relate to "Cannot reconnect after unpair device with smart phone".
debug wit...
How can i give command from android device to ble board to get the percentage, temperature, or reset or shutdown the device with the help of receiving command from android...
I'm trying to register the SIM card of the 9160 DK at nRF Connect website,
but the website is always showing "still working..." for more than 15 minutes.
Do you have a...
Hello,
I am experimenting with setting up a network via grouping in the following manner.
Bulb_1 will be put into identification mode, and Switch_1 will detect Bulb_1...
Hello,
I am trying to send gps data using MQTT protocol. For this purpose I wanted to combine MQTT simple example with the GPS example. I added all the methods/dependencies...
