the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
On my macOS Mojave, I have followed the 'Getting Started Assistant' in setting up the development environment for the nRF9160 but I am unable to load the asset tracker project...
Hello,
I am developing firmware for nRF52810 with SDK 15.0.0 and I need the OTA DFU features (buttonless DFU to be more specific) but there is no DFU demo for nRF52810....
Hi,
When trying to drive a motor driver, my nRF52 DK board is damaged with power rail 3.0V dropped to 0.5V.
After I desolder the interface MCU, the supply comes back...
Hi,
What is the limitation in terms of the number of bytes that can be sent over the UART to be sent over BLE on the usart ble example? I tried sending 32 bytes and it worked...
Greetings,
I am working with serial mesh (nrfSDk 15.2 for mesh 3.1 with softdevice s132_nrf52_6.1.0) .
1. I followed the serial example available and its working.
2...
Env: nrf52, sdk15, ubuntu, SES
Hi First steps on fstorage. As I just need to store and read an array of some bytes I have chosen fstorage
and I got this as output...
Hi,
I am working on DFU over Mesh for quite a bit now. I did run few tests but never run the DFU on a large network comprising of 100+ nodes. SO, I have questions about...
Hello
We are trying to finalize the layout we need for a nRF9160 module with gps capabilities.
I have downloaded the schematics and layout for the devkit V0.8.5.
what...
my code based on file "nRF5_SDK_14.0.0_3bcc1f7.zip".my hardware based on nrf52832QFAA.
my options set as:
project “bootloader_secure_ble”：
project “ ble_app_hrs ”with...
I changed the bootloader size by changing the flash start address (in the .icf file, from 0xf8000, to 0xf7000). I just want to check what other files/settings needs to be...
I need to use pin 8 and pin 20 as outputs on the nRF52 DK, to be transferred to a custom board built with the nRF52810. I'm using SDK v15.x.x.
I need to drive PWM output...
Im trying to detect power off. The signal power off looks like:
The time to get 0V equal 15seconds. GPIO EVENT and COMP do not see changes in the voltage level, they are...
Hi folks!
I'm working with a couple of nrf52832 on custom boards. I'm trying to implement a procedure for firmware updates. I've already played with the examples from the...
I have found many questions regarding passing bonding information from the application to the bootloader (e.g. https://devzone.nordicsemi.com/f/nordic-q-a/34497/dfu-with-bonds...
