Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Custom board, ncs v1.5.0, modem FW v1.2.3, SES v5.34a. The code is based on the Asset Tracker (v1), LTE with PSM, motion-activated GPS, using MQTT to send messages to a private...
Hi guys, I'm struggling on multiple fronts to make the system building up again after NCS upgrade to 1.5.0. This is the last uncanny warning I get at build time. Please give...
Using SD S140 7.2.0 SDK 17 (nRF52840).
I cannot write to internal flash addresses above 0x78000.
I am calling nrf_fstorage_init setting start_addr=0x68000 and end_addr...
Hello,
I am looking at the TX start-up current for the nRF5340 mentioned here (last 2 entries in the Radio current consumption (Transmitter) table) in the product specification...
Hello,
I am having an issue where I am trying to send a payload in the ACK in the ESB protocol. The issue is when the PRX gets a payload it was not expecting (i.e anything...
Hi Nordic team,
Please guide to resolve the error .
While trying to convert the model_handler.c to model_handler.cpp the below deceleration shows multiple compilation...
Summary: What are advantage bullet factors of Zephyr RTOS over FreeRTOS to choose this in nRF Connect SDK v1.5.0
Details: We have Implemented our previous project...
Due to a particularly stupid thing I have done on another chip, I have ended up depending on the ability to advertise a short name and a long name. However, when I build an...
I'm new to using micro controllers and for a project i have the nRF52 controller and i am trying to perform an OTA FW update using web bluetooth. When i connect to the board...
The problem is I can't figure out a way to use the shield pins on the board (P20) to program an external MCU (nrf52832). It just refuses to do so it always programs the onboard...
Hi,
We are using I2C to communicate with a sensor from the thingy:91. The sensor need either 3.3 V or 5 V I/O voltage levels to communicate.
As we understand it, the...
Hi all,
I am trying to develop a simple windows application using pc-ble-driver writing my own C# bindings on a nrf52840 dongle with nrf-ble-driver-sd_api_v6-mt-4_1_4.dll...
Hi,
I am running the example code:C:\nRF5_SDK_17.0.2_d674dde\examples\ble_central_and_peripheral\experimental\ble_app_multirole_lesc
I am using PCA10040 dev board.
When...
I am attempting to use a one shot application timer. This works fine when I use the event handler to perform a specific task toggle an LED for example. But I would really...
Good afternoon,
We have developed a new equipment based on the nrf52840. We use sofldevice 's140_nrf52_6.1.0_softdevice' and we use bonding with static pin.
We have setup...
