If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi all,
I have RaspPi_OT_Border_Router_Demo_v4.1.0-1.alpha image for BorderRouter and need to work with Command lines in Command line Interface(CLI) and with diag commands...
Hello,
I have recently received nrf5340 development kit.
To get my very first stamps of programming given precompiled image peripheral heart rate, I
1. Connected board...
Hello,
I want to evaluate the ble_app_buttonless_dfu example (C:\nRF5SDK160098a08e\examples\ble_peripheral\ble_app_buttonless_dfu). I am using the nRF5 SDK 16.0.0, IAR EWARM...
I have an nRF52840 - install the BLE Sniffer Software on it - play a littel Bit - happy :-)
(dont help me to scan the communication between 2 devices - but thats a other...
Hi,
I need to test the data rate capacity between a nrf52840 and a smartphone. Smartphone being the central device and nrf52840 being the peripheral device. I have an...
Hi,
What hardware configuration settings that I need to change when moving from Development Kit(NRF52832) to BL651(NRF52810)?
I can run all examples from "nRF5_SDK_17...
Based on the datasheet table 166 can the drive strength for SCL/SDA pin is mentioned to be selected as S0D1 can it be changed to H0D1 drive strength? Since based on the IBIS...
Hi! What is the proper use of sd_ble_gap_adv_stop in SDK 15? I'm using nrf52832 in my application but can't seen to find a corret way to stop advertising.
Looking on ble_gap...
Hi all,
I'm using Raspberry Pi with Nordic dongle and flashed the Nordic Alpha 4.1.0.1 image to make it as BorderRouter in NCP design.
I have EFR32device and have flashed...
Hi
I'm using nrf52832 custom board with 14.2.0 SDK version and trying to communicate TWI interface with LTC2631 DAC converter. I tested my sensor hardware with Arduino and...
DK 52840 DK
description ： for example ：we use 52840 DK start a adv at 37 channel,when this packet transmission finished， the radio will change from TX to RX，so how we get...
Hello
I am working on BLE custom board NRF52832 design. I have made 3 PCB for it and out of three, 1 PCB working fine and rest of the two connects with the BLE but doesn...
Brand new Thingy91 PCA20035 out of the box.
Plugging in the USB and turning it on, the nRF Connect Programmer alternates between 'Select device' and 'No devices available...
Hi, after a couple of months of inactivity I try to rebuild my Zephyr-based application under nRF Connect SDK, tag 1.3.0. I’m dumb-founded to see this unexpected print hereunder...
