I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
To automate some testing procedures, I was wondering if it is possible to use the firmware, which runs on an nRF5x to connect to nRF Connect for Desktop, but with a...
Hello all,
I'm fairly new to BLE and Linux BlueZ.
I'm trying to interface a Mikrobus BLE module based on nrf52840dk to our Yocto based Linux SBC (Rugged board i.MX6-UL...
Hi Nordic Team,
I am new to embedded developing and I am learning about logging data while working on nRF connect sdk" .
kit:nrf5340
SDK: nRF connect SDK v1.5.0...
I'm finding that the MCUBoot stays stuck in bootloader mode sometimes when using a CONFIG_BOOT_SERIAL_DETECT_PORT.
I've narrowed it down to setting up the GPIO as input...
Dear !!
Good day!!
I want to change the device name using command from mobile along wither after setting the device name i want update the Password, so can you share...
So,
I've got a working framework for my project - a battery powered appliance that will occasionally trigger one of two solenoids, timestamping the operation and subsequently...
I've got an issue where calling a function is overwriting a variable in the calling function. See attached screenshots. In the first, byte is 0x1b. After stepping into the...
Hi,
I am trying to send data over UART to a dispensing unit using Space Parity but am unable to do so since NRF51 only supports Even Parity. Is there any work around through...
Hello, I am trying to implement 1-1 connection between a central and a peripheral, with these (classic) requirements : - when starting central, scan for any peripheral with...
Hi,
I am having some trouble getting optimal power consumption while using the SAADC.
I've tried running the example given here 2766.nRF5_SDK17.0.2_ble_app_beacon_lp_saadc...
Hi,
We are trying to investigate the interval noises of our custom developed sensor board with a digital accelerometer (With SPI interface).
After checking the software...
Hello NRF ,
I have used NRF52832 with BLE advertise and peripherals connected on two different I2Cs ( temp sensor and gyro sensor ), One SPI( LCD Display ) , three GPIO...
I'm working with nRF52840 dongle, i installed nRF Connect for Desktop on windows but the led didn't start pulsing red. Has anyone else had an issue like this?
I am using SDK 16.0.0. I want to switch from a NON-CONNECTABLE, NON-SCANNABLE advertisement to a CONNECTABLE, SCANNABLE advertisement. I launch the first advertisement and...
