I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Hi,
I'm working on a Keyboard&Touchpad project, very similar configuration with Smart Remote 2, so I'm considering to use nRF24LU1+ as receiver's MCU. The receiver will be...
Help, I want to run NRF_LOG_ENABLED builds but occasionally I want the device to sleep for (many) minutes, so I wish to turn off the NRF_LOG_UART backend since it consumes...
I plan to test BLE and Zigbee communication range in multiprotocol examples.
And I haven't found how to configure Zigbee tx power.
Questions:
1. Is the tx power of BLE...
Hi all,
I am trying to interface HI-3585 with nrf52832 through SPI which works fine. Now i have merged the code with saadc program so as to transmit adc values through HI...
Hello.
I am building nRF Mesh SDK using cmake (gcc).
After successful building the code, I flashed hex file to nRF 52 DK.
I want to know free space in DK after flashing...
We want to use nRF52840 as advanced USB - UART converter to control end device (see structure below).
We already checked that our end device is working fine by external...
Dear Support
I’m having a problem erasing the network configuration data in the flash.
We are using nrf5_SDK_for_Mesh_v2.0.1 with the flash manager according to this post...
I am new and trying to install and run samples on Raspi 3B but cannot. Have anyone worked with Raspi 3B and nrf52840 dongle and please give me some instructions.
Hi I'm using Android Studio 3.2 and github.com/.../Android-nRF-UART My Samsung SM-G570Y (Android 7.0 API 24) works no problems but the Samsung SM-G955F (Android 8.0.0, API...
Hi. I am developing a gateway using SDK15 and nRF52840.
I'm advertising 4 devices every 20ms.
Theoretically, it should be scanned 50 times each, but in reality it is...
I tried to add an additional characteristic to NUS service as below.
However, any mobile apps could find only existing Nordic Rx and Nordic Tx characteristics, other than...
- Go to the following link:
www.nordicsemi.com/.../
- Scroll down the page and click the "Downloads" tab
- Go to the nRF52840-DK-HW tab and click "Download file"
...
Dear Nordic Team
-> what is the pinout of the TRACE connector of the nrf52840DK (PCA10056) board ?
I need to connect wires onto P0.11 and P1.00 GPIO, and the trace...
I'm using the nRF52832 SoC through Rigado's BMD 350. For initializing BLE, I'm using the Thingy52 firmware code as the hardware mostly reflects that of the Thingy52. My hardware...
Hi,
I am using nRF_SDK_15.0.0_a53641 and writing a program with keil.
I am receiving data from the sensor with TWI communication and writing it to the sensor by SPI communication...
Hi everyone,
Device : nRF52832
SDK version : 14.2
Softdevice : S132 v5.0
I am facing a problem when changing the interrupt priority dynamically. Let me explain the...
