Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi guys:
a. I use a uart dfu bootloader(loacation: SDK-location\nRF5_SDK_15.0.0_a53641a\nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10056_uart) in 52840 soc...
What is the ADC internal reference voltage (0.6V) tolerance at room temperature and over the full operating temperature range?
Or is it same as the value specified in the...
I am using NRF52840dk boards to make an openThread mesh network with CoAP. There is an example in NRF-SDK for coap client and another example for coap server. I used them...
I know there is an ongoing global semiconductor crisis. In the products, we decided to switch to NRF52/53 family products as core MCU. However, we're having hard time getting...
Hi,
Currently our system is using printf() to print some debug messages to the Segger debug terminal. Now we would like to reroute these messages to a UART port.
We are...
Hi there,
My nrf52840 DK seems dead. I want to recover it.
What I did:
Put the nrf52840 DK into Bootloader mode by pressing the "IF BOOT/RESET" button while powering...
Hi,
I'm working with pc-ble-driver and a PCA10040 devkit.
First, the central sends a data length update:
This returns no error (0), and on the BLE_GAP_EVT_DATA_LENGTH_UPDATE...
Hello,
we have a question about the usage of FDS. The data to save has a length of 1200 words. So the virtual page size is set to:
#define FDS_VIRTUAL_PAGE_SIZE 2048...
Hello,
I am using "pheripheral heartrate" example on SES, but I can not integrate SPI or ADC. How can I add "nrf_spi.h" and "nrf_adc.h" and relative C files on that project...
I'm using an NRF52811 and trying to configure the UARTE for Tx & Rx at 57600 baud but I'm having trouble with the Rx. I think I am dropping bytes and so want to try and exploit...
Hi,
please find attached some patches to improve the code quality of the SDK
1. Make ble_db_discovery_evt_t a const ptr
2. make p_string in ble_nus_c_string_send...
Hello,
i just loaded compilled peripheral_uart project without modification from nrfConnect sdk v1.5.1 to nrf52840 of the nrf9160 dk
and here is the output on uart output...
Hi, I successfully implemented a custom BLE service using this tutorial from Nordic. Also, thanks to a Nordic engineer, I have the QSPI example merged with the ble_app_template...
Hi,
When I open an example project in the Segger Embedded Studios I can first build without a problem. When I change the target
device under Debugger in the project options...
Hi,
I'm struggling to adjust the BLE_blinky example in the Segger Embedded Studio from the NRF52810 to the NRF52811.
I tried to follow the documentation from here (...
