Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
I'm implementing the full modem firmware update as demonstrated by the sample located at /samples/nrf9160/http_update/full_modem_update.
A bunch of it works. I'm able to...
I try to modify one of the pc-ble-driver examples to work together with my PCA10040 and the Nordic UART Service example in my Qt application, but the application doesn´t discover...
Hello,
I'm currently using SDK v17.0.2 with the NRF52840 on nRF52840-DK Board. After going through the example code of "nrfx_spim" I was able to get up and running. I...
Hi, I am trying to integrate DWS3000 (UWB) APIs, given here to nRF52840 with BLE stack enabled such that my firmware can blink Eddystone packets at the same time when UWB...
The customer requested that pairing be prohibited under certain circumstances, so I called API
sd_ble_gap_sec_params_reply(m_conn_handle, BLE_GAP_SEC_STATUS_PAIRING_NOT_SUPP...
in ~/ncs/zephyr/samples/hello_world/prj.conf or in ~/ncs/zephyr/boards/arm/nrf9160dk_nrf9160/nrf9160dk_nrf9160ns_defconfig
CONFIG_I2C=y
in my nrf9160dk_nrf9160ns.overlay...
Hi,
We are using nrf52833 for measuring angle of arrival. We got IQ samples from the device we need to calculate the phase difference from that IQ sample. please explain...
Hi, we have an application using an nRF52832 without a SD that we want to put into low power / sleep mode to save battery.
What commands should we use to do this and wake...
Hi,
I am using ppi to read some continuous data from a sensor through SPI and i got it working, it reads data in evry 8ms from the sensor through ppi.
but it fails when...
I am working with the secure bootloader example. I copied the firmware zip package to my phone. It contains only application.hex in the package, there is no softdevice or...
Hi,
I am working on an application where the device will be in off mode(only timer and BSP initialized in main ) initially and when I long press button_0 for 5 sec the remaining...
Hi,
We are looking for DFU mode GATT protocol source code for reference to implement custom android application which uses DFU mode GATT service to update firmware distribution...
My static code analysis tool complained something, so I took a deeper look and found the following declaration inconsistencies as of nRF5 SDK v17.0.2 in the DTM area. So I...
I am in the process of programming the MAX30105 sensor with the NRF52840 board to obtain the oxygen concentration values I tried to use the library that already exists in...
