I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
hi,
i am using nrf51422 with sdk13.3.0 and soft device 130
i want to send 69 bytes of data,which is the best way to increase packet size
By creating custom service,can...
Hello All,
I made 2 custom boards, both mount a n52840 QIAAC0 chip. I was able to program them using the "ble_app_uart peripheral" and "ble_app_uart_c" codes that I found...
Hi,
Board: nRF52840 PCA10056 Development kit
Keiluvision 5
SoftDevice : S140
nRF-SDK 15.2
SDK example code: ble_app_uart
Hi, I want to change the BLE range...
Hi,
nRF905 is still manufactured, right? I didnot see anything on Nordicsemi, but I've seen on Farnell's web page "No Longer Manufactured" and on digikey it was not available...
Hi!
I'm using nrf8001 to send twenty 20-byte packets to a phone application. The connection interval I use is 30ms. However, I takes 5 seconds to send the data to the phone...
Hi, I want to advertise each 3times every 5seconds as sometimes beacon scanner can't read it so I need 3times in series advertising.
in main() I added 3times advertising...
Hi there, I am working on NRF52 DK, SDK15.2 with SD 6.1.0, The issue I am facing is that the DFU service is appearing on Android device and I can update apps using NRF toolkit...
I am trying to connect nrf52832 with custom android app, after connection established beacon sends message. Sometimes I can establish the connection after 8 tries, sometimes...
Hi,
I'm working on a project which uses two nRF51822 (SD130 and SDK v11.0) on mobile devices. Device A is continously advertising and device B scans for a fixed interval...
I'm looking to sync an ADC reading with the PWM output. I'm using PPI for this but fails to make it synchronise properly with the PWM.
I'm getting interrupts and sampled...
Hello,i am using nrfsdk with softdevice 6.0.0 in my application and by using it i am trying to connect my mobile uart application with my BLE .but i am facing some issues...
Hallo all
I have an appliation using the LOG for TX output to uart,
I want to maintain this code but to add RX based on the app_fifo_init,
how can they coexist ?
thanks...
Hi,
I would like to use the nrf52 as my bluetooth end device, which inturn has to communicate with the Bluetooth IOT gateway like Rigado module or Nordic gateway APP(which...
Hi
I am using SDK 14.0.0 and soft device S130.
I am planning to add SPI functionality to BLE's sample code.
However, when moving to the next instruction after SPI data...
