Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
DK 52840 DK
description ： for example ：we use 52840 DK start a adv at 37 channel,when this packet transmission finished， the radio will change from TX to RX，so how we get...
Hello
I am working on BLE custom board NRF52832 design. I have made 3 PCB for it and out of three, 1 PCB working fine and rest of the two connects with the BLE but doesn...
Brand new Thingy91 PCA20035 out of the box.
Plugging in the USB and turning it on, the nRF Connect Programmer alternates between 'Select device' and 'No devices available...
Hi, after a couple of months of inactivity I try to rebuild my Zephyr-based application under nRF Connect SDK, tag 1.3.0. I’m dumb-founded to see this unexpected print hereunder...
Hello,
Is there any complex documentation how to implement MSC on custom block device ?
I need to implement NAND flash memory in specific way, but I don't understand how...
Hi,all
How to filter the scanned broadcasters by short name ?
I have been set 'CNT' define, and compiled without any errors,and it worked, but the filtering strategy didn...
Hi,
To automate some testing procedures, I was wondering if it is possible to use the firmware, which runs on an nRF5x to connect to nRF Connect for Desktop, but with a...
Hello all,
I'm fairly new to BLE and Linux BlueZ.
I'm trying to interface a Mikrobus BLE module based on nrf52840dk to our Yocto based Linux SBC (Rugged board i.MX6-UL...
Hi Nordic Team,
I am new to embedded developing and I am learning about logging data while working on nRF connect sdk" .
kit:nrf5340
SDK: nRF connect SDK v1.5.0...
I'm finding that the MCUBoot stays stuck in bootloader mode sometimes when using a CONFIG_BOOT_SERIAL_DETECT_PORT.
I've narrowed it down to setting up the GPIO as input...
Dear !!
Good day!!
I want to change the device name using command from mobile along wither after setting the device name i want update the Password, so can you share...
So,
I've got a working framework for my project - a battery powered appliance that will occasionally trigger one of two solenoids, timestamping the operation and subsequently...
I've got an issue where calling a function is overwriting a variable in the calling function. See attached screenshots. In the first, byte is 0x1b. After stepping into the...
