When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hello all,
I'm fairly new to BLE and Linux BlueZ.
I'm trying to interface a Mikrobus BLE module based on nrf52840dk to our Yocto based Linux SBC (Rugged board i.MX6-UL...
Hi Nordic Team,
I am new to embedded developing and I am learning about logging data while working on nRF connect sdk" .
kit:nrf5340
SDK: nRF connect SDK v1.5.0...
I'm finding that the MCUBoot stays stuck in bootloader mode sometimes when using a CONFIG_BOOT_SERIAL_DETECT_PORT.
I've narrowed it down to setting up the GPIO as input...
Dear !!
Good day!!
I want to change the device name using command from mobile along wither after setting the device name i want update the Password, so can you share...
So,
I've got a working framework for my project - a battery powered appliance that will occasionally trigger one of two solenoids, timestamping the operation and subsequently...
I've got an issue where calling a function is overwriting a variable in the calling function. See attached screenshots. In the first, byte is 0x1b. After stepping into the...
Hi,
I am trying to send data over UART to a dispensing unit using Space Parity but am unable to do so since NRF51 only supports Even Parity. Is there any work around through...
Hello, I am trying to implement 1-1 connection between a central and a peripheral, with these (classic) requirements : - when starting central, scan for any peripheral with...
Hi,
I am having some trouble getting optimal power consumption while using the SAADC.
I've tried running the example given here 2766.nRF5_SDK17.0.2_ble_app_beacon_lp_saadc...
Hi,
We are trying to investigate the interval noises of our custom developed sensor board with a digital accelerometer (With SPI interface).
After checking the software...
Hello NRF ,
I have used NRF52832 with BLE advertise and peripherals connected on two different I2Cs ( temp sensor and gyro sensor ), One SPI( LCD Display ) , three GPIO...
I'm working with nRF52840 dongle, i installed nRF Connect for Desktop on windows but the led didn't start pulsing red. Has anyone else had an issue like this?
I am using SDK 16.0.0. I want to switch from a NON-CONNECTABLE, NON-SCANNABLE advertisement to a CONNECTABLE, SCANNABLE advertisement. I launch the first advertisement and...
Hello, I have a bit of a weird case. I'm sending data over Bluetooth. In the begging, I wrote whole data handling in the main.c main loop. everything worked nicely, so I have...
