hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
The BLE scanner I developed does not scan devices with RSSI less than -80 dBm. However, it is stated in the datasheet that the nRF52832 chip has a sensitivity of -96 dBm....
Hello,
I have a problem when I want connect my phone to do a DFU for this I use the Bootloader Secure Example. My Phone is a Samsung Note 9 and I have the last update for...
Hello,
We are using nRF52840 with SDK 15.2.0, a bootloader and the SoftDevice. We communicate with another microcontroller (a STM) with I2C. The nRF52840 is the master...
I want to use the Direct Test Mode software in the nRFConnect App for radio testing on my custom board, but it's not working. I suppose this is happening because I connect...
Hey all
I'm working on a BLE device using a nRf52840 SOC and for some tests now I've to measure the RSSI on a specific BLE channel (e.g. ch 37). What I've done so far...
Hi
I am using NC version 1.5.0 Dk version 0.15.0 .I am trying to get the AGPS data ..it's working sometimes and some times I'm facing the following error.Can you please...
Hi,
Is it possible to run a freeRTOS project on nRF52805?
I've follow the instructions from "Developing for the nRF52805 with nRF5 SDK" on the simple "blinky" example...
Hi,
I want to know a few things about sending large packets via BLE using nRF52 SDK 15.0 and above.
I am able to send the packets larger upto 128 Bytes. But i want to...
We are working on our development board contain the nRF52840. We also use Bluetooth Low Energy to load wirelessly the updated code with the DFU and it's working properly....
Dear Sir/Madam,
We are planning to devellop a remote control for resque equipement.
The remote controller and the host should pair 1 to 1. Pairing should be easy for the...
Hi.
I am going to make my own PCB with nrf52832.
Before making it, I have to check debugging through P20 in nrf52832 DK.
I have two nrf52832 DKs with SDK17.0.0.
I...
I am working on zigbee network where I wanted to get the tree of whole network but could not find any utility from nordic which can provide those info, so I have started developing...
Hi,
In my application, I'm trying to restart emulation because I want to switch from the NDEF static payload mode to ISO-DEP mode. The problem is that when I stop emulation...
