Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using an NRF 51422 DK, SDK 12.3, and Soft Device S130. I am also a beginner to development with Nordic Products, and RSSI collection in general. I am using the...
Hi Nordic team, I'm working with nRF52840 PCA10056 , base on Thread_Zigbee_ v4.1.0 , and light_control example. I modifed, try to add temp_measurement ZCL in all light_bulb...
Hi ,
My environment:
nrf5340 dk board
nrf connect sdk
segger studio IDE
.
I want to test spi loop back without any connections.
I don't want to connect any...
Hello, zephyr pwm driver documentation and samples , shows clearly how to generate a PWM output using nrf52840 dk. However, we need to synchronize the PWM output to an input...
Hello, how can we configure the counter in an nrfx52840 dev board to count pulses on an input pin in zephyr? There is a counter driver in zephyr, but there doesn't seem to...
What I'm trying to do, is probably very simple. I hope.
In the following code which works fine.
I want to scan not using Coded PHY
Then change back to using Coded PHY...
question here, I am using nRF52840 device with zephyr application & MCUboot + SMP service the DFU is now done using: https://github.com/apache/mynewt-mcumgr-cli or using Nordic...
I have a application using 52805 with no external crystal, I found that Timer1/2 not working, anyone have idea can Timer run with internal HFCLK(HFINT)? by the way, everything...
Hello i am trying to send 4 bytes of data over ble with custom service but im getting an unknown error and i am stuck in a dead end please help me .I am greatfull to any kind...
Hi,
I try to change the endianess of transmitted data from Little Endian to Big Endian.
So for example when I want to transmit a value uint32_t valueTx = 0xAABBCCDD
...
I have nrf 9160 DK board and sdk v 1.4.2 ( downloaded from nrfconnect toolchain manager ) .
For example blinky , which is the DTS file it takes and how do I modify it ?...
Hi,
Firmware v1.31
I have a question about using those call functions https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/include/modem/lte_lc.html#c.lte_lc_deinit...
Hi,
I cannot compile the example/ble_peripheral/ble_app_uart project (others examples are compiled ok). I didin't make any changes. The errors are some files in the library...
Hi,
I am working on a personal project, and I have added my own functions in the ble_app_template project. I was trying to add the UART functionality in this project, based...
