Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am attempting to use a one shot application timer. This works fine when I use the event handler to perform a specific task toggle an LED for example. But I would really...
Good afternoon,
We have developed a new equipment based on the nrf52840. We use sofldevice 's140_nrf52_6.1.0_softdevice' and we use bonding with static pin.
We have setup...
Hi,
Is it possible to generate Complimentary PWM in nrF840? Do i need to use the PWM in Individual mode?
My application is a synchronous buck converter
thanks,
th...
Hi all,
I have RaspPi_OT_Border_Router_Demo_v4.1.0-1.alpha image for BorderRouter and need to work with Command lines in Command line Interface(CLI) and with diag commands...
Hello,
I have recently received nrf5340 development kit.
To get my very first stamps of programming given precompiled image peripheral heart rate, I
1. Connected board...
Hello,
I want to evaluate the ble_app_buttonless_dfu example (C:\nRF5SDK160098a08e\examples\ble_peripheral\ble_app_buttonless_dfu). I am using the nRF5 SDK 16.0.0, IAR EWARM...
I have an nRF52840 - install the BLE Sniffer Software on it - play a littel Bit - happy :-)
(dont help me to scan the communication between 2 devices - but thats a other...
Hi,
I need to test the data rate capacity between a nrf52840 and a smartphone. Smartphone being the central device and nrf52840 being the peripheral device. I have an...
Hi,
What hardware configuration settings that I need to change when moving from Development Kit(NRF52832) to BL651(NRF52810)?
I can run all examples from "nRF5_SDK_17...
Based on the datasheet table 166 can the drive strength for SCL/SDA pin is mentioned to be selected as S0D1 can it be changed to H0D1 drive strength? Since based on the IBIS...
Hi! What is the proper use of sd_ble_gap_adv_stop in SDK 15? I'm using nrf52832 in my application but can't seen to find a corret way to stop advertising.
Looking on ble_gap...
Hi all,
I'm using Raspberry Pi with Nordic dongle and flashed the Nordic Alpha 4.1.0.1 image to make it as BorderRouter in NCP design.
I have EFR32device and have flashed...
Hi
I'm using nrf52832 custom board with 14.2.0 SDK version and trying to communicate TWI interface with LTC2631 DAC converter. I tested my sensor hardware with Arduino and...
DK 52840 DK
description ： for example ：we use 52840 DK start a adv at 37 channel,when this packet transmission finished， the radio will change from TX to RX，so how we get...
Hello
I am working on BLE custom board NRF52832 design. I have made 3 PCB for it and out of three, 1 PCB working fine and rest of the two connects with the BLE but doesn...
