Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello Nordic Team;
The Vdd value range for the nRF9160 is 3.00 V to 5.5 V. We will use li-PO battery in our system. Can I power the nRF9160 directly from the battery without...
Hi,
I am using Nordic thingy 52 for my application, Now I need to blink LED for 5 seconds on Board when ever a condition is satisfied. But in schematic of Nordic thingy...
Board: nRF51-DK (nRF51422 chip)
SDK: 12.3.0
SoftDevice: S130
Compilation settings
Optimization level O1
Debug information generated
I have seen lot of...
Hi.
I am going to make my own PCB with nrf52832.
Before making it, I have to check debugging through P20 in nrf52832 DK.
I have two nrf52832 DKs with SDK17.0.0....
Platform: nRF5340-DK
Tools: I am using SDK 1.5.0 (but seen on earlier SDKs too)
Configuration: Using high speed spi pins whether for SPI1 or SPI4
If I use SPI1 I see...
Hey guys i wanted to ask you for help on IOS BLE i am currently seeing that nRF Connect seems to work fine over BLE Connection with some devices on Android and as far as i...
Hi,
I'm using NRF52840 in order to connect to a mobile app via BLE.
When connection to IOS, I have an event called BLE_GAP_EVT_PHY_UPDATE_REQUEST.
This event handle...
Hi,
Greetings!
We are exploring nRF9160 SIP DK and Thingy91.
Here we have understood that it has GPA and LTE-M.
We wish to use it for India region in moving objects...
We are using the advanced UARTE library to get advantage of EasyDMA to receive data from a LTE module.
We also implemented hardware flow control. THe problem is that the...
Hi fellow devs:) I'd really appreciate some advice on this please. I've come to a bit of a dead-end. Hopefully you can spot a mistake I've made. I am trying to produce a low...
Hi,
-I have a custom board using nrf 52832 and I have interfaced sensor using an SPI interface. -I am using SDK 15.2.0 and SPI driver. -I am collecting raw data and send...
Hi, When I test the SPI with extern flash W25Q64, The SDK default configuration seems to be too low powe, After SPI initialization is complete, The GPIO drive is configured...
Hello All ,
I want to use nRF 52810 Bluetooth feature in one of my application. The application is supposed to be highly power optimized. Sharing below some details about...
I am currently working on an application running on the nRF52 DK which will use some inputs and output to interface with the environment. Its a BLE application and those inputs...
