Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
The temp accuracy is stated at +/-5C. Does that include using piece-wise linear terms for accuracy? Is there any data on accuracy over a narrow temp range such as 0-40C? ...
Hei, I couldn't really find a question regarding this use-case.
I'm hoping to interface a USB (2.0) charging capability to my design and thus I need to have a communication...
Hi Nordic,
Does FDS affect PPI ADC acquisition when writing data? The test found that once the FDS is written to the data, the ADC data returned by the PPI ADC is fixed...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to ask about WDT and softdevice (centre).
The WDT setting is 2s timeout and the WDT...
Platform: windows
hardware revisions: PCA10056
nrf5 SDK: 15.2.0
mesh SDK: V3.0.0
IDE: Keil MDK \ SEGGER embeded studio
I want to use keil to develop mesh projects...
Hi, I has a question.when I start the mode of debug ,the start code execution will automatically open.I dont know why .(I use sdk12.3,and the chip IC is 52832). compile the...
Hello, I'm trying to get an ANT+ peripheral example to work on an Adafruit nRF52832 breakout module. I'm using the 15.0 SDK, SD S212 and SES with a J-Link to program over...
Hi,all,
Now I am using nRF52832 to develop a Tire Pressure Monitoring System ,but I serached the ANT website and found that " a TPMS profile is "in the works". ANT+ members...
hi
i need to test the BT OTA test ( total radiated power (TRP), total isotropic sensitivity (TIS)
https://www.mwrf.com/test-measurement/ble-antenna-testing-helps-optimize...
Hello, maybe my answer didn´t get to you correctly. Referring to my post 10 days ago, I am still stuck controlling the joining procedure .
https://devzone.nordicsemi.com...
HELLO
I would like to know how to test RF for nrf24l0.
Of course, the RF test I'm talking about is frequency modulation for KC certificate
Previously, nrf24le1 was...
Hi,
Just to be clear, you are looking for reference DFU controller firmware for the Host MCU, in order to upgrade the firmware on the nRF52832。
I also need this feature...
Hello Developers,
I have configured a mesh network where I have a gateway node and multiple relays to relay messages from End nodes (sensors)
My question is the following...
Hi. I am working with nrf52832 trying to get Bluetooth and UART and a I2C peripheral working at the same time. I had a working version of the I2C peripheral and UART working...
hi.......
i need to run the program continuously using timer ......and want to check the data every one minute how to do that
i have seen timer example .. i am confused...
