I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
I am using the nRF GFX library to print some text on an LCD. The font, prepared with The Dot Factory v.0.1.4, is stored in flash per the examples in the sdk.
The problem...
I am manually installing the nRF Connect SDK using these instructions https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing.html and in paragraph 4...
Although I have a fair amount of experience with PIC microcontrollers, I am new to the nRF52 and I am finding it difficult to make the transition. However I have been given...
HI
I use nRF5_SDK_17.0.2_d674dde ble_app_hids_keyboard。 I want to composite KB and Media player。
but only KB can work。
I find many people have this question。 but do...
hi
I use nRF5_SDK_17.0.2_d674dde. delete bonds have some problem.
1. when poweron before into main loop， use delete bond is ok。 can run to PM_EVT_PEERS_DELETE_SUCCEEDED...
Hi, I have the same issue with https://devzone.nordicsemi.com/f/nordic-q-a/59096/nrf52832-module-can-t-connect-j-link-anymore-after-flashing-zephyr-program-onto-it but the...
Hi, I got nRF5340 DK board and trying to run sample projects such as peripheral_lbs, peripherad_gatt_dm, etc. using SEGGER Embedded studio but BLE advertisement doesn't work...
Custom board, ncs v1.4.0, modem FW v1.2.3, SES v5.34a. The code is based on the Asset Tracker (v1), LTE with PSM, motion-activated GPS, using MQTT to send messages to private...
In the ble app uart example, I need the BLE device to be able to send out a null character. I noticed when I receive a message with a null character at the end from the UART...
Hello. I am receiving an input of 1 Hz. ADC is receiving 12 bits. uart's baud rate is 1000000. ADC input is output as UART raw data.
To do this, I modified the following...
hi,
I've found the sample for direction findings in the sdk-nrf github master branch (sdk-nrf/samples/bluetooth/direction_finding_connectionless_tx)
Will this code work...
Hello,
I want to extend the at_client sample with vanilla Mbed TLS (delivered with the SDK) supporting TLS. Later on, I want to be able to modify the Mbed TLS vanilla implementation...
In the past I was able to get the Serial LTE Example application working over UART0 on the pins used in my custom board. I did so by adding a file called nrf9160dk_nrf9160...
Hi,
I am using spim3 16Mhz and sometimes the spi tx data had the first byte as same as previous last byte and sensor can not react and timed out because of the wrong data...
