I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
hi
I use nRF5_SDK_17.0.2_d674dde. delete bonds have some problem.
1. when poweron before into main loop， use delete bond is ok。 can run to PM_EVT_PEERS_DELETE_SUCCEEDED...
Hi, I have the same issue with https://devzone.nordicsemi.com/f/nordic-q-a/59096/nrf52832-module-can-t-connect-j-link-anymore-after-flashing-zephyr-program-onto-it but the...
Hi, I got nRF5340 DK board and trying to run sample projects such as peripheral_lbs, peripherad_gatt_dm, etc. using SEGGER Embedded studio but BLE advertisement doesn't work...
Custom board, ncs v1.4.0, modem FW v1.2.3, SES v5.34a. The code is based on the Asset Tracker (v1), LTE with PSM, motion-activated GPS, using MQTT to send messages to private...
In the ble app uart example, I need the BLE device to be able to send out a null character. I noticed when I receive a message with a null character at the end from the UART...
Hello. I am receiving an input of 1 Hz. ADC is receiving 12 bits. uart's baud rate is 1000000. ADC input is output as UART raw data.
To do this, I modified the following...
hi,
I've found the sample for direction findings in the sdk-nrf github master branch (sdk-nrf/samples/bluetooth/direction_finding_connectionless_tx)
Will this code work...
Hello,
I want to extend the at_client sample with vanilla Mbed TLS (delivered with the SDK) supporting TLS. Later on, I want to be able to modify the Mbed TLS vanilla implementation...
In the past I was able to get the Serial LTE Example application working over UART0 on the pins used in my custom board. I did so by adding a file called nrf9160dk_nrf9160...
Hi,
I am using spim3 16Mhz and sometimes the spi tx data had the first byte as same as previous last byte and sensor can not react and timed out because of the wrong data...
Hello,
I am using NCS v1.3.0 and nrf52840 dk board. In the central_uart demo example, there is a macro called "BT_LE_SCAN_PASSIVE" which has an option set as "BT_LE_SCAN_OPT_FILTER_DUPLICATE...
I have had 3 nrf52840 dongles burn out after a few weeks running on 3V from 2x 1.5 alkaline batteries, powering the dongle from VBUS. Initially, the current draw was 900uA...
Hi Team,
I am looking for an isochronous stream feature for one of our application use cases.
I am using NRF52840 now. Will this feature come as an FW/SW upgrade or in...
1. regarding about trying to make the GPIO pin as 1.8V output for nrf52840
I try to make my board to work with theGPIO output 1.8V, I have calling the code below after the...
