Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi there,
When I program my nrf24le1 in Keil uVision, I notice that when I load the program to the flash memory of the connected motherboard6700 with the nrf24 radio module...
I have downloaded the Kiel and uVision file (the nrf Probe) found here: https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF24-series and have gone through...
Hi,
I am using Keil 5 (downloaded with this link: https://www.keil.com/demo/eval/c51.htm ) and have downloaded the nrfProbe to this file. This is being used to program...
Hi, I am try to implement UART SERIAL Bootloader for my device and I just need to perform DFU using uart serial
I have tested the code and bootloader. My query is
Without...
When I run the "ble_app_blinky_pca10040_s132" example from SDK 17.0.2 and 15.2.0, right after Connected I'm seeing that device is Disconnected from device.
I tried with...
We need to programatically (on the Raspberry Pi using Python) send and receive characters to and from a smartphone using a custom service over BTLE. I have used the blinky...
I am trying to communicate with my IOT using wired uart serial port. I am using 840(MCU) (with softdevice #113).
code:
My Issue: Each time I am trying to run it while...
Hi,
I am trying to reduce the consumption of my Thingy91 device in idle mode. I am working with NCSv1.3 and the example asset_tracker. I am currently registering 0.60mA...
In our NRF9160 application, we do not have a UART available and have to implement other means of logging crashes.
We have written our own k_sys_fatal_error_handler but it...
I am using a generic nRF52 dev board with the Arduino nRF52 core . I am trying to get a sample BLE service to display, but it cannot find it on my BLE scanner. After I couldn...
Hi,
I am trying to read read all nearby base stations' Cell ID, TAC, MNC, MCC.
Is this even possible to do with this DK?
At this point I have found these commands...
Hello,
I am trying the UDP sample for the nRF9160 DK board, using the iBasis SIM card that came with the kit.
The problem is that it does not register onto the network...
Hello,
I’m trying to interface the MAX32664GWEB+T sensor hub with the NRF52 by using I2C, I’m wondering if you could provide me any recommendation, libraries or codes for...
What I want to do is do UART communication (UART_1) between nRF52840 and nRF9160.
From the nRF52840 side, uart_poll_out is OK, From the nRF9160 side, uart_poll_out examined...
