Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
hi.
i use nrf52840 to d evelop a keyboard .i connect and be bonded by a pc,now i want to delect to the bond info of the pc,and after this ,my adv cant be scan by this pc...
Hi Nordic Tech Support team,
One of my customers is having some problem with UARTE implementation. They used the ble_app_uart example ( pca10056 with SoftDevice 113 )...
Hello Everyone,
We are developing one custom device using open thread protocol.
We are using SDK - nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71 and Dev-kit - nRF52840...
IN Establishing the friendship,I received the following error
/** The Low Power node was not able to send transport command due to internal fault. */ NRF_MESH_EVT_FRIENDSHIP_TERMINATED_REASON_INTERNAL_TX_FAILED...
I want to send ADC data over bluetooth. When I searched, I found the following contents.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsds_s132%2FSDS%2Fs1xx%2Fble_data_throughput...
I am using the nRF51422 development kit with the SDK 11. I am trying to run the proximity application located in ble_peripherals. When the project is build I am receiving...
Hi,
I am using ble_sdk_app_hids_keyboard example:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_hids_keyboard.html...
Hello, I lived in Taiwan and I followed nRF9160 DK Getting Started and met a problem at establishing connection with nRF Cloud with my board.
The previous steps are all...
Hello, I'm trying to run C++ code on the nrf52832 but I'm getting an Hard Fault when sending a floating point to an ostream, like in "std::cout << 13.5f;". The FPU is enabled...
Hi All,
I'm trying to interface a SD Card with nRF52840 DK.
I've got a SD Card socket and a FAT32 formatted 8GB sd card.
When I run, fatfs example , I get following...
hello,
i am using nrf52840 in our customised board with sdk 15.2 and trying to achieve long range with coded phy using long range demo example as base now i could be able...
Hi,
I have two boards NRF52840 DK and I wanted to use example for BLE Central&Peripheral NRF Relay. I have just run example with Heart Rate peripheral and I can see that...
Hi there,
When I program my nrf24le1 in Keil uVision, I notice that when I load the program to the flash memory of the connected motherboard6700 with the nrf24 radio module...
I have downloaded the Kiel and uVision file (the nrf Probe) found here: https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF24-series and have gone through...
Hi,
I am using Keil 5 (downloaded with this link: https://www.keil.com/demo/eval/c51.htm ) and have downloaded the nrfProbe to this file. This is being used to program...
