Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
I'm building a firmware for nRF52 which is using app timer v2 with RTC1. After a while, app_timer starts running many times faster than normal, and I'm not sure why. Nothing...
I use pc-ble-driver to control nRF52840 dongle. I want to speed up scanning of advertising time.
So I change SCAN_INTERVAL and SCAN_WINDOW.
How can I modify the parameters...
The enocean_switch example has MESH-config example, to store data in FLASH, within the mesh rules.
I use it in my app, IT WORKS, but the biggest data array what I can store...
hello folk,
I am working on nrf52840, I want it to assign Static UID of any kind that even won't change after the device gets reset.
I have already gone through "FICR...
Hi,
I am looking at using the nrf5340/nrf9160 in a device. In this device, I need to have high endurance storage of some data that must be kept secret, integrity checked...
Hi,
My project involves an nRF52840 DK connected to an accelerometer on a breadboard, connecting to my Mac via USB-micro.
I'm editing the twi_scanner SES project so...
nRF5_SDK_17.0.0_9d13099,
IDE Segger V4.52c
soft device s132
I took ble_app_uart example, and then modified it to run I2C, SPI. everything is working fine
problem I...
I have a question about how to perform DFU over Mesh.
I'm using nRF52840 device.
Following the steps at the URL below (Configuring and performing DFU over Mesh), I'm trying...
nRF5_SDK_17.0.0_9d13099,
IDE Segger V4.52c
soft device s132
Reading the spec of nrf52832 I saw I2S, I need to interface a MIC, so I selected I2S Mic SPH0645, but after...
Hello,
is there a way to record Advertising Packets on all three channels (37,38,39) simultaneously using 3 individual nRF52840-Dongles and piping the output to a stream...
Both Devzone and Mesh SDK 5.0 are mentioned that store user data in mesh should using flash manager.
But read the source code of the mesh SDK , the mesh SDK already called...
We have used nus profile for over a year, and it has worked as expected. Now we added security to the BLE connection, with ble sec connection enabled, it works as expected...
Hello everyone,
I am currently in the process of designing a prototype using the nRF9160 and I use the Nordic-Thingy91 as a reference for some parts. The Thingy91 uses the...
Is there any supporting documentation or information about remote assignment of receivers.
The only reference I have been able to locate is sparse and not backed by anything...
Hi guys,
I'm pretty new in embedded development without using an Arduino. I tried to use the sensor APIs of BMI270 and BMP388 recently, but didn't get it to work.
The...
