Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I want to create a 1MHz timer using TIMER2.
I try to start the timer with the following settings, but the device probably hangs.
I also use app_timer, is it a problem...
Hello, Not so long ago I asked this question and the solution I was given is still working for the devices I was using. Now I've received a new version of the device in which...
Hello,
I am using nRF52832 DK module(for master), and breakout board(for slaves, 4-slaves).
I have some problem while BLE communication.
First, I am wondering if I can...
Hi,
I'm getting error on connect to cloud server (socket.nouslogic.com:443) with error code is 45 ( EOPNOTSUPP).
Here are detail:
1. Using https_client example on nRF...
Hi,
I am going to use a timer in my code which includes ble_app_uart (using app_timer) and saadc examples. I need this timer to read time during the program.
I know...
what I use project is "ble_thread_dyn_template" , Is there any way to replace the app's UART console with 'BLE' - i.e. instead of receiving 'ot' commands from UART console...
I need to read (and clear) the general purpose retention register. I cant start the Soft Device just yet, so cant use the sd_power_gpregret_get and sd_power_gpregret_clr functions...
Hi there!
I'm back again, with another possibly stupid mistake. I'm using ARMGCC in combination with Make, nRF5 SDK, nRF SDK for Mesh, FreeRTOS and C++. I wrote my own mesh...
Hi Dev team,
I am currently using the NCS v1.5.0 and have a Thingy91 v1.4.0 with me. I want to test the FOTA v2 update from the nRF Cloud to the Thingy91.
I tried using...
I am trying to tune my NFC antenna . The antenna is printed on the pcb. The same Laird antenna is used in my pcb. Based on the antenna tuning white paper I am trying to tune...
When I connect my Thingy 91 to my usb port open up nrf Connect and push Sw3 and turn on the board power I do not get any devices to show up under device selection in rf connect...
In our application the prospective Nordic NRF5340 MCU is to communicate with another MCU at the maximum 3Mbps.
Can this speed ( 3Mbps) be achieved on NRF5340?
As mentioned...
Hello, I'm hoping that I missed something in the code and not something that might be inherent with nus and fds. Combining SDK 15.3 template, uart and fds examples, with some...
Hi,
We have a working solution on the SDK15.0.0 with a custom board based on nrf52832 s132. I'm using the nrf52dk PCA10040 to program my boards. For this board we use...
