Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hi,
im use the example of nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_hids_keyboard
and i change the code of static void hids_init(void) like this:
and...
Hi
i have installed segger emstudio and almost all dependencies but still can't able to build a project. my main target is to work with nrf9160 dk but without an hardware...
Hello!
I'm working on a project with the new nRF5340 & Zephyr and I'm trying to get two SPI peripherals on the same bus sampling data correctly. It's a simple program thus...
Hello,May I ask you a question?
Hardware model: NRF51822 SDK version: SDKv9.0.0 SoftDevice:s110.
I used the interface in the pstorage.c file to realize the storage of...
Hi there,
I'm just trying to start to code my project. I want to stream 48k 16 bit audio from one nrf52840 dongle to the other one. I only need one way transfer.
I have...
Hi,
I want to use dtm project to test RF PHY performance about NRF5340. But after downloading dtm project and empty app project, NRF5340 can work normally from output RTT...
Hello I use nrf52832 and sdk v17.0.
I'm testing the firmware using custom pcb. Sometimes it stops altogether if there is an error in the firmware during the test.
The...
Hi. I'm testing our new product that can be extend ranges using FEM.
For best performance, I'm matching impedance between antenna and FEM.
But my major is not wireless...
Hello, I have a problem with my own designed board, It has nRF52832 and some other sensors which communicate over SPI, also I have a SD card on the same bus that works fine...
Hello,
In my code I am reading from a sensor and want to check if the float value returned is out of range. In order to do so I would like to be able to calculate the absolute...
i have just blinked the LED and trying to pwm
i have written a simple led blinking program like this one below
#include <stdbool.h> #include <stdint.h> #include "nrf_delay...
I'm trying to diagnose frequent (80%) DFU failures that I'm seeing with our Android application using Buttonless mode.
Our target can be 100% reliably updated with our app...
Hello,
I would like to program the NRF52840DK to send ZigBee beacon(not beacon request) to the end devices, but I cannot seem to find the API, etc. to do so.
Or perhaps...
Hello NRF ,
I am not able to run any of the the BLE peripheral example codes from the SDK12.2.0 ( Nordic NRF 52 SDK ) .
The reason I am using 12.2.0 is I have a sensor...
