Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi
I am developing RX device to connect with Smart Remote 3.
The RX device system is Linux embedded. I need to run OTA function in Linux embedded to update SR3 F/W.
...
Hi,
I am using STM32F030C6 MCU with Laird BL651 module.
Keil-IDE v5, windows 7(64-bit) system configuration.
I need to get the sample code for the application development...
Hello, I have following problem.
My DK is not recognized by J-Link / nRFgo Studio.
I tried to reflash J-Link by pressing BOOT/RESET and then drag and drop J-Link OB...
Hi,
I would like to update the Device Information Service's (DIS) serial number characteristic to reflect the actual serial number assigned by our production equipment....
Hi, I am using the following setup: Wireshark 2.6.5 (updated yesterday) Sniffer 2.0.0-beta-3 (nrfsniffer200beta312oct20181c2a221.zip) nRF52840-DK (used by the sniffer) nRF52840...
I have a custom board that uses Nordic NRF52832 as MCU. For laying out crystals, BLE part and decoupling capacitors, I used reference layout from documentation.
32 MHz crystal...
Hi everyone,
My hw/sw configuration:
- nRF52840 - sdk 15.0.0 - softdevice: s140_nrf52_6.0.0
I would like to change the device name and update it in advertising packet...
Hi All,
I have been working on ipv6 over ble on zephyr RTOS to form mesh network.I have been successfully integrated "rpl_node"(which is in zephyr/samples/net/rpl_node)...
Hi guys,
I have very strange problem with the Android phone when connect with nrf51822.
After connection, I used update parameters to set the parameters on the phone side...
Hello,
I am attempting to program nRF52 DK modules to communicate using the UART over BLE central and peripheral roles as in the examples provided in SDK 15.2. The data...
hello, I have used NRF52810 TWIM for 24LC08 communication, and I got a problem.
when I want to read data from 24LC08, if the length is not lager than 255, every thing is...
Dear all,
Good morning,
We are using nrf52832 as our main mcu. Our current consumption in system-off mode in custom board is around 3.2 mA which is very high and we want...
HI devzone
We now use NRF52832 to implement TDMA protocol.
In our application, there is one primary node and six sub-nodes.The communication process is as follows:
After...
I want to add simple on off switch model via SDK 2.2.0.
I'm already add client model to project,when provisioner add client node,Provisioner RTT jump error opcode status...
Hello Everyone,
Maybe this is a very silly question.
I am trying to implement timer in nrf51822 with S130, SDK11.
Code snippet:
void TIMER1_IRQHandler(void)
...
