Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
Hi,
I am trying to compile ble_advertising.c file for a specific application based on nrf52840 and I am getting the following error:
nRF5_SDK_15.3.0_59ac345/components...
I am working with an nRF52840 on a custom board. Our device has a number of sensor attached in various ways including spim, twim, uart. I've used the ble_app_blinky as a starting...
Hi Dev Team,
I am enhancing my Thingy91 application using the mqtt_simple sample and NCS v1.5.0. I am basically connecting to the MQTT broker, sending data and then disconnecting...
I am using nrf52840 as PTX and nrf24l01+ as PRX. The application I am working on requires me to send 30 bytes from PTX to PRX at a 2 kHz packet rate. If both devices are near...
I am trying to make ble communication work with I2C but i cant make it work i dont understand what is the issue the code is being build but it does not advertise can someone...
I'm building a firmware for nRF52 which is using app timer v2 with RTC1. After a while, app_timer starts running many times faster than normal, and I'm not sure why. Nothing...
I use pc-ble-driver to control nRF52840 dongle. I want to speed up scanning of advertising time.
So I change SCAN_INTERVAL and SCAN_WINDOW.
How can I modify the parameters...
The enocean_switch example has MESH-config example, to store data in FLASH, within the mesh rules.
I use it in my app, IT WORKS, but the biggest data array what I can store...
hello folk,
I am working on nrf52840, I want it to assign Static UID of any kind that even won't change after the device gets reset.
I have already gone through "FICR...
Hi,
I am looking at using the nrf5340/nrf9160 in a device. In this device, I need to have high endurance storage of some data that must be kept secret, integrity checked...
Hi,
My project involves an nRF52840 DK connected to an accelerometer on a breadboard, connecting to my Mac via USB-micro.
I'm editing the twi_scanner SES project so...
nRF5_SDK_17.0.0_9d13099,
IDE Segger V4.52c
soft device s132
I took ble_app_uart example, and then modified it to run I2C, SPI. everything is working fine
problem I...
I have a question about how to perform DFU over Mesh.
I'm using nRF52840 device.
Following the steps at the URL below (Configuring and performing DFU over Mesh), I'm trying...
nRF5_SDK_17.0.0_9d13099,
IDE Segger V4.52c
soft device s132
Reading the spec of nrf52832 I saw I2S, I need to interface a MIC, so I selected I2S Mic SPH0645, but after...
