When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hello,
I am trying to connect my nRF9160 but am running into some trouble. Only LED 3 blinks for about 3 minutes and then just stays on without blinking; LED 4 never blinks...
Dears
I double the ble_nus_init as below ,I can get 2 service bouth have 2 characteritic.
as below:
err_code = nrf_ble_qwr_init (&m_qwr, &qwr_init); APP_ERROR_CHECK...
I am facing issue with programming of own developed nRF52810QFAA board. I used Pins 25 (clock) and 26 (data) along with Vcc and Gnd to flash device. I tried with two boards...
Hi, May I use slip library code for commercial? I have a project that uses an MCU communicates with an NRF52 BLE module. To upgrade program of BLE module, I flash the bootloader...
I’m mitgrating from nRF52832 TO nRF52810 and softdevice s132 to s112 and having compile issues.
I understand that NRF peripheral has been removed on the nRF52810 but I do...
This how i make it happend:
1.programe softdevice and bootloader.
2.generate app dfu package.
3.upgarde app via nRF Toolbox
4.It's running, all things is seem ok....
Hi, I've been working with SDK11, and now I have to move my project to SDK14 due to some issues with the old SDK. In SDK11 I could just use Keil's "Manage Run-Time Enviroments...
Hello,
I am trying to execute the SPI slave example from sdk15.2 on my NRF52832 Dev board (PCA10040 1.2.1).
I am using stm32f0 dev board as the master and transmitting...
Let suppose using the dynamic multiprotocol ZigBee + Softdevice application with OTA upgrade possibility. I would like to use the app_timer (along with app_scheduler) to trigger...
I want to change MIN_CONN_INTERVAL and MAX_CONN_INTERVAL values when I connected to phone.
I build function that handler events and send the update to ble_conn_params_change_conn_params...
Hi Nordic DevZone,
I am trying to include the UART driver module (.c .h file pairs) into my new project in SEGGER Embedded Studio.
I have done the following:
I...
Hi,
I have a few issues with flashing the dongle. I am using [ \nRF5_SDK_12.3.0_d7731ad\examples\peripheral\blinky\pca10031\s130\arm5_no_packs ]
When flashing the soft...
I am trying to accomplish the following:
Read values from a number of sensors
Put the device in sleep mode (while keeping the samples from sensors in memory so that...
