When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
hello, I have used NRF52810 TWIM for 24LC08 communication, and I got a problem.
when I want to read data from 24LC08, if the length is not lager than 255, every thing is...
Dear all,
Good morning,
We are using nrf52832 as our main mcu. Our current consumption in system-off mode in custom board is around 3.2 mA which is very high and we want...
HI devzone
We now use NRF52832 to implement TDMA protocol.
In our application, there is one primary node and six sub-nodes.The communication process is as follows:
After...
I want to add simple on off switch model via SDK 2.2.0.
I'm already add client model to project,when provisioner add client node,Provisioner RTT jump error opcode status...
Hello Everyone,
Maybe this is a very silly question.
I am trying to implement timer in nrf51822 with S130, SDK11.
Code snippet:
void TIMER1_IRQHandler(void)
...
Hi,
i Have two development kits where one acts as uart central and another acts as uart peripheral .
In that i have given the peripherals different names( DEVICE_NAME...
Hi, I would like to ask how can i get the current consumption that was stated in the datasheet which is 0.7uA and the value I get from the reading is about 8-9 uA.
Is...
Hi team,
I am using sdk 14.2 ,nrf52840 DK board.
I am getting the following error while running nrf5-mpu-ble-simple code in keil. <error> app: Error 0x000D (13) at line...
hi.....
i am using nrf52832 ........
i want to wake up my device from sleep mode ... i have used the command for sleep mode sd_app_evt_wait() ...... i dono what command...
Hi Sir,
We plan to use the serial DFU to upgrade the 52832 (Host MCU + 52832), we use UART as the communicate interface.
Do we have the example code for reference for...
Hi,
I'm experiencing frequent crashes in the softdevice on an nrf52832, running SD version 6.0.0 with SDK 15.0. The crash seems to occur when interfacing to the device over...
So I can live with the 60uA power draw I get shortly after a power cycle but the strangest thing happens. Over a short period of time the power consumption ramps up to, well...
Hardware: customized board based on PCA10056
SW: nRF5_SDK_15.2.0_9412b96
Change:
Merge ble_app_blinky example into blinky_rtc_freertos.
/cfs-file/__key/support-attachments...
NRF52832
SDK 15.2
Two MCUs communicate through serial port. If the other MCU is not powered on, nrf52832 will not run (LOG error > app: Fatal error). If UART is not initialized...
Hi everyone,
These days, I am thinking about how to make some upgrade about the sound module of thingy52.
It would be quite funny to make some other sound samples rather...
