Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
hello, I have used NRF52810 TWIM for 24LC08 communication, and I got a problem.
when I want to read data from 24LC08, if the length is not lager than 255, every thing is...
Dear all,
Good morning,
We are using nrf52832 as our main mcu. Our current consumption in system-off mode in custom board is around 3.2 mA which is very high and we want...
HI devzone
We now use NRF52832 to implement TDMA protocol.
In our application, there is one primary node and six sub-nodes.The communication process is as follows:
After...
I want to add simple on off switch model via SDK 2.2.0.
I'm already add client model to project,when provisioner add client node,Provisioner RTT jump error opcode status...
Hello Everyone,
Maybe this is a very silly question.
I am trying to implement timer in nrf51822 with S130, SDK11.
Code snippet:
void TIMER1_IRQHandler(void)
...
Hi,
i Have two development kits where one acts as uart central and another acts as uart peripheral .
In that i have given the peripherals different names( DEVICE_NAME...
Hi, I would like to ask how can i get the current consumption that was stated in the datasheet which is 0.7uA and the value I get from the reading is about 8-9 uA.
Is...
Hi team,
I am using sdk 14.2 ,nrf52840 DK board.
I am getting the following error while running nrf5-mpu-ble-simple code in keil. <error> app: Error 0x000D (13) at line...
hi.....
i am using nrf52832 ........
i want to wake up my device from sleep mode ... i have used the command for sleep mode sd_app_evt_wait() ...... i dono what command...
Hi Sir,
We plan to use the serial DFU to upgrade the 52832 (Host MCU + 52832), we use UART as the communicate interface.
Do we have the example code for reference for...
Hi,
I'm experiencing frequent crashes in the softdevice on an nrf52832, running SD version 6.0.0 with SDK 15.0. The crash seems to occur when interfacing to the device over...
So I can live with the 60uA power draw I get shortly after a power cycle but the strangest thing happens. Over a short period of time the power consumption ramps up to, well...
Hardware: customized board based on PCA10056
SW: nRF5_SDK_15.2.0_9412b96
Change:
Merge ble_app_blinky example into blinky_rtc_freertos.
/cfs-file/__key/support-attachments...
NRF52832
SDK 15.2
Two MCUs communicate through serial port. If the other MCU is not powered on, nrf52832 will not run (LOG error > app: Fatal error). If UART is not initialized...
Hi everyone,
These days, I am thinking about how to make some upgrade about the sound module of thingy52.
It would be quite funny to make some other sound samples rather...
