Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a custom board based on the nRF9160 and using nRF Connect SDK v3.0.2. We’ve developed the board in-house and integrated the npm1300 PMIC as part of...
Hello,
For our emission tests in an anechoic chamber we need to be sure that the BT antenna is up and running. Of course we cannot connect via BT from outside the chamber...
Hello Nordic users and employees,
I'm having a small dilemma. The device I'm building runs on the nRF51822 and needs to store a small number of bytes off to the side and...
Hello, it is to my understanding that profile & service do not have fixed forms. Services make up profiles and you can choose how many and what services make up a profile...
I I'm running the ble_app_blinky example under pca10028 on the nrf dongle pca10031 using sdk11. The dongle disconnects after 24 seconds. Can anyone point to me what is the...
A typical classic or BLE get paired with the phone/central, and normally the central can decide to forget/unpair it. In this case, the device (nordic chipset) which previously...
I had created application with enabling the UART service(as in Ble_uart_app example) and tried to update the Rx characteristics of UART service in connectable mode through...
I'm sending a write authorization reply using sd_ble_gatts_rw_authorize_reply() in response to a standard Write Request with one byte of data. When I set the gatt_status to...
I am currently dealing with a strange problem when trying to use DFU OTA. When I enter DFU mode on Master Control Panel and try and update I get the following two error messages...
Does anyone have a working copy of ble_cps.c\h
The BDS (version 1.0.2095.0) plugin (v.1.2.4) does not generate code that compiles under IAR EWB
IAR ANSI C/C++ Compiler...
Hi there, I'm definitely a newb when it comes to wireless communication and communication protocols so I'd like this question to be answered at a higher level than what I...
Hello,
I am implementing a central which is scanning for advertising packets using s130, SDK11, nRF51822 and based on example ble_app_hrs_rscs_relay.
I get the advertising...
Hi,
I'm trying to porte my code from micro_esb to nrf_esb. My need is to know when a frame with correct address is received. This frame don't need to be valid just received...
Is there any way to use more than 4 buttons using app_button or BSP library?
It seems that GPIOTE can handle only 4 pin. Am I right??
uint32_t err_code;
// Button configuration...
Hi,
I am wondering if it is possible to change the RADIO data rate using SoftDevice.
I am developing an application which do not need an high data transfer but it would...
Hi,
Migration to nRF5_SDK_12.0.0_12f24da has broken build of some our projects at link stage (region RAM overflowed with stack).
During investigation I found that nfc_t2t_lib_gcc...
