Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hi
I want to know how to use ppi to wake up CPU from IDLE mode.
I've tried to use timer timeout event for triggering Port Event and wake up CPU, but can't assign NRF_GPIOTE...
I have been using a module of nRF52832. I write the Direct test mode in the module, to measure the current consumption of the Tx and Rx. DTM setting is + 4dBm, DCDC off. As...
Hello,
I try to send about 80kB of data between 2 beacons and I have encountered some problem that I got no idea how to resolve.
I have managed to connect devices, discover...
There are certain design decisions that break C++, or at least the separation of concern between allocation of entities and the use of entities.
For example:
typedef...
Hi there,
Is there any chance future SDKs with the nrf52 have support for Mifare Classic cards? The example with the Adafruit shows an Ultralight tag, but it would be useful...
I have a USB dongle with nRF24LU1+ chip (marking "NRF E LU1P16 1438AD").
I have several problems with programming this chip via SPI. For example after entering programming...
Dear Nordic developer：
I am very eager to have the "Android-nRF-Connect" of the source code! I found the scan and DFU from the "Android-nRF-Toolbox" function, I also need...
I'm trying to get going on an nRF51 project using the compiler on mbed.org, but if I create a new project using the nRF51 DK and use any of the example BLE apps as templates...
I am runing the example on custom board 16k ram, i have configured the linker file correctly as shown below. but all the ble_peripheral application doesnt run (not advertising...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
DEVICE_MANAGER_MAX_BONDS is no more than 10.
That means that no more than 10 difference devices (smart phones) can switch the device to DFU mode?? (with boding).
Am I right...
Dear Nordic developer：
I am very eager to have the "Android-nRF-Connect" of the source code! I found the scan and DFU from the "Android-nRF-Toolbox" function, I also need...
Hi
I cannot find the minimum pulse length to trigger wakeup using DETECT from GPIO hw pin configured as SENSE pin in the data sheet for nRF51822.
Ex: set PIN_CNF[0].SENSE...
