We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi,
I have a question related to GATT Services in BLE, so not strictly a nrf51 question although it's related to one of the examples. The example for the (Human) Thermometer...
I have a BLE wearable (Pebble watch) that I wish to detect using the nrf51822 evaluation kit. I can use the Control Panel to see the pebble. I would like to be able to us...
When I put the ESB lib into my BLE Soft Device the MDK tell me that it have some error in it.
What's wrong in my project? if I need ESB+BLE what should I do?(NRF51822+SDK6...
So I installed the Master Control panel software, plugged in the PCA10000, whereupon I was advised to update the firmware in the PCA10000. The firmware update apparently failed...
Hi,
I am trying to get the s130 example to work on my PCA10028 board nRF51.
First I had to change the starting adresse from 0x1C000 to 0x1D000.
I guess that this is due...
There are only the last version nRF51822 Product Specification V3.1 on the web. However, I need a V2.0 PS. So, where can I download the nRF51822 PS V2.0?
Hi,
I wrote a very simple program which compare the analog reference input 0 (P0.00) with AIN0 (P0.26) and generate an interrupt on cross using Low Power comparator on...
Could you update the ble-app-lbs example for SDK 7.1.0?
github.com/.../nrf51-ble-app-lbs
I haven’t been able to get it work.
Since the led_char_add() uses these setters...
Is there a limit to the number of characteristics per (custom) service?
After some testing, it looks like 20 is the maximum (21 causes the device to stop functioning) ...
Hi All,
I am an electronics engineer but new to nRF51822 programming. I have used the PCA10000 & PCA10001 using Nordic SDK, using nRF Studio etc. In nRF Studio, you can...
I'm using SD110, and in my application I have an array of 64, 32-bit integers.
Typically, the client will only need to read 1 of the 64 values, or write to one of the 64...
I'm just getting started with the nRF51-DK, and I'm still confused about which SD I need to load, and which roles I need to support aka GAP and GATT.
My end application...
Hi,
It seems to me that pin assignment and package is the same for both nRF chips. Can I solder nRF51422 chip instead of nRF51822 for ANT testing purposes on my PCA10004...
