Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hi,
this is how I initialize and enable LPCOMP
nrf_drv_lpcomp_config_t lpcompconfig = {
{NRF_LPCOMP_REF_SUPPLY_SEVEN_EIGHT, NRF_LPCOMP_DETECT_CROSS},
APP_IRQ_PRIORITY_LOW...
Hi,
I wonder if BLE_ERROR_NO_TX_BUFFERS(s110) and BLE_ERROR_NO_TX_PACKETS(s130) have same meaning.
These marco variables are defined in ble_err.h.
Thank you.
HI,ALL,
i am so sorry for my silly question here.
In ble CORE SPEC,
i saw a sentense (Version 4.2 [Vol 1, Part A])below:
"Device L is shown in the same locality...
Hi,
The SDK6.1 bootloader seems to have problems when used on a Laird BL600 module.
I'm using a BL600 with the SDK6.1 and SD7.1. I want to implement the bootloader in...
Hello!
As per documentation, RSSI is measured during the time, when particular packet is being received. In particular, nRF51822 Product Specification v3.1 states RSSIperiod...
Hi, i have a NRF51-DK (nRF51822 - PCA10028) board and using SDKv10 with SoftDevice S110.
I read everything i could find about this topic and i see people claiming data rate...
I am looking to synchronize collecting of data from outside devices with the connection interval of the nRF51822 and the S110 vers. 8.0 softdevice. Are there specific events...
I want to send big amount of data (10kb) with characteristic of 16 bytes. when the phone side is subscribed to notification I run a loop of data sending.
how can I synchronize...
I have read through the forum on this and I am still not completely clear. Here are my questions:
Can I create characteristics that are larger than 20 bytes? The Bluetooth...
In looking at the nRF51 UART Example I'm wondering about data loss over the Bluetooth interface.
When bytes are sent to the host, is there a re-transmission mechanism somewhere...
Hello,
I was just editing the handling of sent packets and I wanted to evaluate the contents of the ble_gattc_evt_write_rsp_t struct which is part of the BLE_GATTC_EVT_WRITE_RSP...
Hello,
im using NRF 51822 with SDK 10 / S110 8.0. Im working on a project that includes one or two timers (initialized by APP_timer function), the ble calender (like discriebed...
Hi,
Because I didn't want to keep with the last question when this is a tottaly new one, so created another question.
I've tried to get this project to work:
github.com...
We have a communication problem between nRF24LU1+ and nRF24L01+ chipsets. nRF24L01+ uses STM32F4xx MCU on board.
Is there an RF sniffer that sniff the protocol?
