I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi:
I use spi0(0x40003000) to wirte data to external flash(W25Q64) with SD8.0(sdk8.0.if I write data without sd, it is OK), and when program run to rx_data[number_of_txd_bytes...
A friend of mine asked me to help with thinking about a solution to create a RF communication between 8 robots and 1 access point. Not a lot of traffic, just to signal that...
Hi everyone,
We are making a BLE peripheral that measures some data and keeps it ready for the mobile phone to connect & poll the data.
The data should be private and...
I am trying to use the template to create my own application. In two places I have read, that to add my own services, I just "Double-click the Serives folder in the Project...
Hello everyone,
I had some troubles some time ago with Softdevice s120, and finally solved it to work with nRF51822 thanks to Aryan .
The problem is that, when I upload...
I'm following the official tutorial for using pstorage and this the simplest test code I've come up with:
static pstorage_handle_t base_handle;
static void test_pstorage_cb_handler...
Hi
i started some time ago with building a simple peripheral device, and started form the led-button service example.
In there, device manager was not used. However, in...
Hi,
My application receives assert error from stack. Source file name is src\ll_master.c, line number 831 and error code 0xDEADBEEF.
What this error signifies?
R...
Hello,
In my application I'm using SDK 8.1 with the s110 SoftDevice. In the new version, the pstorage modules have been separated and you need to choose between them.
...
Trying to see how much time my code consumes, I tried the naive approach, calling clock() in the beginning and at the end and comparing the values.
But when I include clock...
I am using the BLE Scanner app on Android to check that my device works.
I have 2 similar problems :
on one device, I can read all characteristics except one. This has...
Hi,
Im trying to use this example to send serial data from GPS module via BLE:
github.com/.../ble_app_uart_low_power_slave
I have disabled hardware flow control since...
Hi
I tried gateway and LED_mesh examples. It worked well. But, I found some issues as below.
When I tired MCP windows application on laptop with PCA10031 dongle...
Hi there,
I am using the nrfjprog to flash the nrf51822 via a J-Tag programmer. Here is the command I used in the command prompt:
nrfjprog --eraseall --programs softdevice...
Haw can I configure ble_app_ uart examples for bonding using? I want to connecting, transmit and receive data throw the UART only with 5 fixed devices.
