Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a custom board based on the nRF9160 and using nRF Connect SDK v3.0.2. We’ve developed the board in-house and integrated the npm1300 PMIC as part of...
Hi everyone,
I was wondering if there are any issues turning on and off the ANT transmitting channel during run-time of nRF51422 with this:
err_code = sd_ant_channel_close...
I want to use master spi mode ,but when I build the file,it is always error.I operate like this ,First I open the project in ble_peripheral\ble_app_hrs\pca10040\s132\arm5_no_packs...
"Hi Guys, my nRF8001 BLE is working perfectly, But recently i was performing regression testing to check BLE connection, their i faced one issue after 10 minutes from nRF8001...
I am using SDK11 on a nRF52 board. I had some success in DFU, but also had issues.
Was able to upload the bootloader successfully using Master control panel. But it always...
I use the nRF52832 IC of WLCSP package.
In addition, it sets as follows:
{.source = NRF_CLOCK_LF_SRC_RC, \
.rc_ctiv = 16, \
.rc_temp_ctiv = 2, \
.xtal_accuracy...
Hi all,
I have a firmware in which I want to use BLE and ANT communication (with Softdevice S310) to send and receive commands from other Nordic devices or smartphones...
Hi,
I modified the code from the tutorial at devzone.nordicsemi.com/.../ to send measurements from my RHT sensor but encountered some basic difficulties. After fitting...
Hi,
I would like to know what the approximate Flash memory and RAM usage by nRF51 chipset would be when using the BLE communication (Let's say I want to send and receive...
Hi everyone
I am working with nRF52 (SD132). I am considering the ble_app_uart example and I'm trying to modify it by setting TIMER1 and TIMER2 peripherals to generate...
I'm trying to update the bootloader over the air, I succeeded to do so following the answer given here
it worked when I didn't change big things in the bootloader , but...
We have noticed that when our application is trying to call GATT disconnect while nRF master app is running, our app fails to disconnect. More over, when our app connects...
Hello everybody,
I am trying to pair module nRF51822 with Heart Rate Monitor device with the Surface Pro running on Windows 10 with no success. I see the module but when...
This question is a follow-up to this post . After performing several tests and understanding that some phone are more limited than others in terms of the number of exchanged...
Hi,
my device resets on executing sd_softdevice_enable(p_clock_lf_cfg, softdevice_fault_handler);
I have external 32KHZ crystal. I also know that software works because...
Hi all,
I have a quesion about reading a value's characteristic in the Android app nrf Master control panel.
I read a value, and i have the good value but i have a letter...
