Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hello,
Since 2 weeks, I use heavily my nRF51-DK (PCA10028), with mbed compiler to make a BLE enabled device.
But, since few days, when i have tried to cut the SB9 in order...
I have a Rev3 nRF51822 chip (CFACA00) on a custom board (no external pull resistors on SWDIO or SWCLK), and I am using nRFgo Studio 1.20.0.2 to program SD 8.0.0 and my Nordic...
I'm using Python bindings 0.5.0 and the connectivity app. On one of our machines that is running tests with the satck/dongle we see it fail a lot with a scrolling of this...
I want to extend the ble_app_multilink_central for pca10028 Example to be able to communicate with a sensor via SPI and then initiate a connection with another pca10028.
...
I'm trying to discover a vendor specific service that has 7 characteristics. However, when I increase BLE_DB_DISCOVERY_MAX_CHAR_PER_SRV to 7 , ble_stack_init() hard faults...
Is it possible to use PPI and RTC to turn the HFCLK on or off ? (external Xtal)
Example - something like this ...
NRF_PPI->CH[9].EEP = (uint32_t) &NRF_RTC0->EVENTS_COMPARE...
hello,
when I use the chip nrf51822(3rd generation),I find that when I open DCDC function,the ability of chip receiving msg is weaken.the receiving distance is shorter a...
I am doing a blob read on two s130's with s120(central). I am getting BLE_GAP_EVT_CONN_PARAM_UPDATE event while doing a continuous blob read.
Some times i get BLE_GAP_EVT_CONN_PARAM_UPDATE...
Hello,
Can you please provide full schematic for nRF52 dev board. I looked though the documentation and there are small bits of the schematic, but I didnt find full sch...
Using a nRF51822-QFAC-A1 on the nRF51-DK I noticed unexpected behavior when starting the HFCLK and LFCLK in rapid succession. This variant reproduces the problem at startup...
I would like to have 31 bytes for my own in advertising and so far I have disabled everything except adv_flags (it still takes 3 bytes cause of length, AD type and value)...
Hi there,
just wanted to know what the practical differences between the JLINK and mbed MCU interface firmwares are.
From what I experience I can only use the UART over...
