I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Hi,
I'm using 3rd Generation of the nRF51822 with SoftDevice 8.0.0 and SDK 10.0.
There is an example in the SDK installation folder which shows how to use the TWI transaction...
Hello,
I have PCA10004 rev 2.2.0 evaluation kit and have tested S110 applications with SDK9.0 and softdevice 8.0.
Now I am working on S130 stack, softdevice v 1.0.0 and...
Hello,
I am working on S130 stack with version 1.0.0 and SDK 9.0 . I am testing the example of ble_app_hrs_rscs_relay_s1 project and it is working as a peripheral but the...
Hi nRF team,
I read somewhere that the sensitivity of the nRF52 is degraded when the internal DCDC is enabled. Can you confirm or dismiss this? If true, what is the sensitivity...
Hi,
I want to use nRF52832 for our new development.
So I have to get examples source code like nRF51822's Keil Pack Installer.
Where Can I get example source code for...
I saw the video of csr mesh network. I want to try something like that using nrf51822. I have read the documentation provided in the link link
. But I only got a rough idea...
Hi,
I am looking for an wearable solution which should be able to full duplex audio transfer over Bluetooth. Is this possible with BLE 4.1/4.2. As here battery life is...
Greetings. Could you provide more information on the issues with GPIO located near the radio in the nRF52 (PS 18.2.1)? Specifically, what is considered "high frequency digital...
I've created a BLE Peripheral project to test maximum possible throughput for the Notify of a single characteristic. I've also created a Central based on the new BLE Central...
Hi: I want use all eight ADC channel, But I don't know how to get different channel conversion result.
I write my code as follow:
void adc_config(void)
{
const...
Hi,
I'm using the 3rd generation of nRF51822 with S110 v8.0.0 and the SDK 10.0.
In my application i'm using the uart core to communicate with the external device.
I'm...
I'm not sure why I didn't notice this sooner.
When trying to do a bonded DFU with a Nexus 6P and Master Control Panel it seems to get stuck in a loop reconnecting.
I...
Hi I trying to connect Altimeter ( mpl 3115a2) to the nrf52 development kit. Can someone guide me how to do it (pin connection). I have followed the example given in the sdk...
