Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
Hi all,
I'm looking into speeding up my workflow using remote development containers on ARM servers, but it seems some tools are missing, nrfutil the first, to run a fully...
Is it possible to see LOG_INF() or LOG_ERR() messages from custom board software when the custom board is connected to a nRF52840DK through connector P20? The custom board...
I have an application that I want to build and run on 5 or 6 target devices including a nRF52840DK, nRF52840 Dongle, and custom boards. There are areas of the code that only...
Hi:
I don't receive any messages in the console during any of the exercises in Lesson 3 and Lesson 4 of the nRF Connect SDK Fundamentals.
No errors occurred during the...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
I'm evaluating nRF52840 as a candidate MCU for our next gen. electronics. I am following the DevAcademy class - all working well until I try to flash the (brand new - just...
Bluetooth connection cache processing - Nordic Q&A - Nordic DevZone - Nordic DevZone
Continuing from last time. After some optimization, the program was able to work. However...
Dear,
I’m experiencing an issue with performing DFU over BLE Mesh. I have a setup with one node acting as provisioner and distributor. This node has a new image loaded ...
Hi,
I am developing an acoustic platform with my custom board with a nRF5340 CLAA chip. The board is recording audio data from two microphones at a sampling rate of 100...
I am using nrf52810 for ble peripherial , is there any sample project which has pass key authorisation , if not what are the changes need to incorporate in peripheral template...
Device Overview
We have developed a smart wearable that sends notifications to our mobile application over BLE. Under normal conditions, the device alternates sensor...
Hi,
Developmente setup: Windows x64, nrf connect for vs code, SDK and toolchain versions 3.0.2.
I was trying to build a proyect for a custom nRF5340 board when I encountered...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Hi,
I’m using the function lte_lc_psm_param_set(rptau, rat) . After connecting to LTE, I call lte_lc_psm_get(&psm_cfg.tau, &psm_cfg.active_time) and receive the following...
In the specs of npm1300 PS, it is suggested that the ADC can measure VBAT, VBAT_7V range, NTC, DIE_TEMP, VSYS, IBAT. However, in the interrupt configuration reported in 7...
