Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Sorry if this is too off topic, I actually don't have any problem with my nrf52840 dongle, but the App I'm communicating with. But maybe someone of you has run into the same...
Hi,
I receive the following build error: "../zephyr-project-v4.1.0/modules/crypto/mbedtls/include/mbedtls/check_config.h:96:2: error: #error "Unsupported partial support...
I found some examples on dev zone how to read RSSI during connected state:
Function report RSSI but as a positive value around 230. How to recalculate it to dB. I see...
I am using nRF Cloud to update firmware on nRF9160 based products in the field. They are connected via LTE Cat-M on Telstra in Australia. The problem is that the download...
Hello Nordic Team,
I'm developing a ranging application on a u-blox NORA-B1 module (which contains an nRF5340) and have encountered a stability issue with the Nordic Distance...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm still new to this but particularly in regards to battery. I have a custom board with a nrf5340 and have been working on reading the voltage. I used the battery sample...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I'm looking to use the nrf connect sdk for development that is compatible with the latest zephyr lts. I believe it will be ncs 2.9.2 compatible with zephyr 3.7.99 (3...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hello Nordic Team,
I’m currently developing a BLE ranging device using the u-blox NORA-B126 module, which integrates an nRF5340 SoC and a Skyworks SKY66112-11 FEM.
I’m...
Hi Nordic team,
I'm currently working on a real-time distance measurement project using channel sounding with the nRF54L15 DKs. I’ve been using the channel_sounding_ras_initiator...
I was looking down at the pinout schematic of the nrf52840 aQFN73, in the schematic provided in the data sheet from v1.1 to v1.11 VSS_PA pin is below ANT pin, but once in...
If I try to compile any of the WIFI examples for the Thingy91x I get a RAM overflow error. The only exception to this is the WIFI scanning example. If I build these for any...
I would like to try the new nRF54H20 but I can’t find its development board. I found this page talking about it, but I can’t find where to buy it online. Has it not been released...
Hi,
I purchased nRF52 DK 2 PCs. PCB labeled
PCA10040
3.0.4
2024.34
boath board are new and box packed. from first time itself. I am not able to flash the board...
