Hi, I am fighting with a bug I found in SDK v2.8.0 for BLE scan filter on a test project as follows: 2 Devices (Ezurio BL653-DVK using the nRF52833), both having central and...
During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Are there any specific points using the external flash of a Thingy:91X?
I tried to adapt the "nrf/samples/cellular/modem_trace_flash" by adding an overlay copied and modified...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
I'm using the nRF9160DK as a BLE-to-LTE bridge, and I have the onboard 52840 configured as my Bluetooth controller. The 9160DK advertises as a peripheral and waits for a connection...
Hi,
I receive the following build error: "../zephyr-project-v4.1.0/modules/crypto/mbedtls/include/mbedtls/check_config.h:96:2: error: #error "Unsupported partial support...
I found some examples on dev zone how to read RSSI during connected state:
Function report RSSI but as a positive value around 230. How to recalculate it to dB. I see...
I am using nRF Cloud to update firmware on nRF9160 based products in the field. They are connected via LTE Cat-M on Telstra in Australia. The problem is that the download...
Hello Nordic Team,
I'm developing a ranging application on a u-blox NORA-B1 module (which contains an nRF5340) and have encountered a stability issue with the Nordic Distance...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm still new to this but particularly in regards to battery. I have a custom board with a nrf5340 and have been working on reading the voltage. I used the battery sample...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I'm looking to use the nrf connect sdk for development that is compatible with the latest zephyr lts. I believe it will be ncs 2.9.2 compatible with zephyr 3.7.99 (3...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hello Nordic Team,
I’m currently developing a BLE ranging device using the u-blox NORA-B126 module, which integrates an nRF5340 SoC and a Skyworks SKY66112-11 FEM.
I’m...
Hi Nordic team,
I'm currently working on a real-time distance measurement project using channel sounding with the nRF54L15 DKs. I’ve been using the channel_sounding_ras_initiator...
I was looking down at the pinout schematic of the nrf52840 aQFN73, in the schematic provided in the data sheet from v1.1 to v1.11 VSS_PA pin is below ANT pin, but once in...
