HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
We would like to achieve following:
Only peripheral devices should advertise data toward only central devices in the same application.
advertising data by peripheral...
Greetings! I'm trying to set up an nRF52 board as an SPI slave so that it would receive chunks of data irregularly from the master device (a Raspberry Pi in this case, if...
Hello,
I would like to know how to implement middle button click in hid mouse, by middle button click i am referring to scroll wheel click and the function associated with...
Hello!!
Is UICR.CLENR0 register disabled on nrf52SoftDevice?(only nRF51Chip??)
When writing with nRFgoStudio("Enable SoftDeviceProtection" CheckBox is on), the firmware...
Hello,
We are trying to build asset tracker based on a modification of board nrf/boards/arm/nrf9160_pca20035.
Every is good until we tried to enable secure bootloader...
Software : C / GCC - SDK 15.0.0 - SD140 6.0.0 - building on multiple platforms. Hardware : nRF52840-DK (Q1AAC0) - and secondary testing on custom board using the Fanstel BT840...
I have been at this for a few days now, I have had a number of compilation errors that I have had to work through and find solutions for, but I am stumped on this current...
I'm trying to use the low-power comparator.
I've started up the comparator using "lpcomp_init()".
Following that, I wish to have a sample event, and then log the result...
I am trying the example here: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_att_mtu.html
I want to lower the sleep...
Hi,
How do I enable Band 1 on my Thingy 91? On your web-page it seems that your base-band supports Band 1, but when I use the following AT-command AT%XCBAND=? I get the...
we are building some IOT devices for home automation, and things were going quite well since we tried to use our mesh network with two cell phones. we tried with two devices...
Hi.
I am using the NRF (Nrf52840) dongle to operate BLE devices (scan \ read \ write).
Is there a way to do it without the NRF connect application and just sending serial...
Hi,
I used Power Profiler Kit to measure our Custom module's current consumption. Everything worked perfectly.
Then I closed PPK SW and used SDK to flash new SW to one...
Hi,
I have connected nrf9160-dk to my laptop and using nRF connect v 2.6.2 with LTE link monitor application.
I am seeing only UART in green and Modem in Red. I am thinking...
