HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
PLEASE CANCEL THIS TICKET
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi all,
I'm a bit confused. After going through available documentation, I thought I had understood that RTC0 was used by the SoftDevice, but that RTC1 was available to...
Hi,
I am using nRFmesh SDK for a project. I have configured all nodes(devices) into one group. Each device will publish message for every three seconds. I am reading the...
Hi,
I need step by step guidance on how to implement BLE MESH ( SIG MESH) using nRF52840 Dongles.
I am trying to connect 5 dongles in MESH config.
Kindly help with...
Hello. I am using nRF52832. The SDK version is 14.0.0. UARTE is used for serial communication with other devices. The baud rate is 38400bps, and a maximum of 20 bytes of data...
Hi, I could not find a way to use Segger Studio debugging features when I have a bootloader for DFU functionality. Is there a way to something like that, because when I click...
I am trying to read temperature, pressure, and humidity data from an Adafruit BME280 sensor using the nRF9160 DK. The communication protocol that I am using is I2C and I am...
Hi,
In our product, we use 9160 GPIO to control the system power. However, we found we can't power off when 9160's modem is in normal mode. But, the system can power off...
Hi,
I want to know if is it possible to send data from the end device to a coordinator without using the periodic reporting method which makes the end device sending the...
Hi,
In our one of the product we are using Nordic nRF52840 MCU and we compiling this application code in windows with SEGGER Embedded STUDIO IDE Version 4.30a and Tool chain...
Hi,
I'm evaluating the nRF5_SDK_v15.0.0 buttonless example OTA DFU bootloaders on a nRF52840-PDK.
The buttonless examples are working well. So I integrated the buttonless...
Hi Everyone,
We are using nRF52810 in our project. It Supports peripheral mode. I didn't find any example code regarding central role. Does nrf52810 supports Central ...
Hi, I'm developing a Zigbee coordinator, but I have this issue during commissioning. The end node is Ikea TRADFRI ambience sensor light (pir), I make a simple test using CLI...
Wanted to use nrf52840 (PCA10059 v1.2.0) as sniffer.need all the related files and sw to use for the same. also not able to downlaod the folder ( github.com/.../nr,so kindly...
