Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
Hi,
I interested in a simple system of a master and slave nrf2460. But how many of these systems would happily coexist in a the same room?
Thanks
Senthil
The Enhanced ShockBurst PTX Project just inits the ESB and start transmitting without ever configing either of the 16MHz or 32kHz clocks (none that I can see at least).
...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
hi.I have a question about synchronization. In main loop, there is a function sd_app_event_wait() which blocks until ble event from softdevice call occurs, so I want to put...
Thought I'd check to see if there were any examples floating around that demonstrate how to dynamically claim memory when the softdevice (s110) is disabled? Any hidden gotchas...
Hi All,
We have embedded windows ce devices, and were thinking of adding ble functionality by connecting a small nrf51822 board through a serial port.
Would it be possible...
I'm currently debugging a daughter card for the nRF8122 evaluation board but there's a higher voltage and current on that daughter card.
I want to know how the IO are connected...
We are developing an application based on S130 V0.9 (orignially S130 V0.5 was used) SoftDevice using development boards PCA10001/PCA10000/Beacon. Main activities of the application...
Hi,
I am trying to use the spi_slave_example on my nordic nrf51822. But i have an issue :
I can build all target and download code to flash memory but nothing happen...
Hello,
What is he meaning of PROTENSET0, PROTENSET1 in sd_flash_protect()?
How can I use this function to set WRITE PROTECT to a certain flash page?
I searched a lot...
Hi,
I need to use nrf51-ble-app-lbs application example to add my customized applications. I have downloaded the project but I'm not able to compile it probably cause I...
Hi All,
I am new in nrf51 development. I have a nRF51-DK kit. I would like to make development in Linux (Debian) only.
I found a lot of documents and I can compile examples...
I have read many times about how BT LE allows devices to run for more than a year on a coin cell.
However, the least current consumption I can obtain while connected is around...
Hello,
We are developing a system using a receiver nRF unit, and multiple transmitter nRF units. The transmitters use the proprietary radio protocol (not bluetooth LE)...
