Hello,
We have the custom board with nRF54H20. The VDD_EXT pin is used to power some GPIO ports of nRF54H20 (P1/P2/P7).
The voltage we see on VDD_EXT is about 1.3V instead...
Hi,
I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4.
Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello,
I am developing a USB Composite Device (= 2 HID devices in one) and I want to add Bluetooth LE functionality.
I am not sure where to start from :) - I am new to...
Hello.
I have adquired PCA10028. I use IAR IDE. I have downloaded an application example for the nrf51422 using the JLINK hardware of the PCA10028 board. I can download...
Dear All,
any opinion on attached antenna design (blue) to the outside of a metal housing?
PCB that flows around an aluminium die cast housing
External to aluminium...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hi all,
I cannot find the exact connector to use for the P19 Debug out header on the pca10028 board.
The one I have has the plastic around too big so it doesn't fit.
...
Hi,
I'm working on a simple ADC application where I sample using analog channel 1 and then read the value through the debugger. However my results are nonsense. I have...
I'm using s120_nrf51_ble_driver on PC.
To connect the BLE dongle, we need to COM port number to be known (parameter of sd_rpc_serial_port_name_set). Is there really no...
I am working on a project on wireless interface between phone and SIM card. I want to use chip nRF51822-CEAA to run SIM card simulation at phone side (include wireless communication...
in nRF51822 product specification a maximum absolute rating of 3.9 Volt is reported, while in electrical specification the maximum voltage is 3.6 Volt.
The question is :...
Hi,
I have tried with the nrfjprog tool and I get the following error:
Command:
nrfjprog.exe --eraseall --programs s110_nrf51822_7.1.0_softdevice.hex --program HILO_P_01...
Am trying to setup a module where I need to send the Serial port ( say from printer/peripheral COM)
to a BLE Peripheral/Central Module. Not sure which SOC or combination...
I have a board built which is a tracking device with a GPS and GSM modem. I'm beginning field testing and have been flashing it with a Segger then disconnecting the Segger...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
I have used the nrf8002 chip before and love it but now I am trying a different application that requires a bit more smarts. I am trying to design a system that can have an...
