Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
I saw in nrf connect sdk 2.9.1 that there was nRF54L15 sample code for Channel Sounding and nRF52833 DK sample code for Direction finding.
But now I want to implement...
Hello,
I am attempting to configure the following setup to support (with an nRF5340 + nRF7002-EK)...
1. nRF7002 on SPI w/ TLS, STA, and FW patches offloaded to QSPI...
Hello,
I am using PAwR (Pe riodic Adve rtsing with Response) in coded PHY (S8) with SDK 2.7.0, following the Nordic demo :
8562.PAwR_Demo.zip
Periodic Advertising with...
Hi all,
I'm working on a BLE peripheral using Zephyr and have run into an issue when enabling both dynamic device naming and long advertising intervals.
I enabled dynamic...
Is there a way to test that the RXD and TXD pins are sending and receiving data on the nrf5340? I am trying to connect these pins to the u-blox ANT-B10-00C using male to female...
Hi guys,
we are using the nRF52833 and have a running application. Now I want to introduce unit tests and stumbled upon ztest . The idea is to add a folder where all the...
I'm using nrf52832 developing my application.
In the past I used sd_ble_opt_set() to set a static pairing code for pairing.
But now a new requirement has emerged, I need...
I am trying to develop Zigbee plug using the demo provided by Nordic. Working on my Intel Macbook Pro 13.7.3
The toolchain and SDK are installed, ver 2.9.1. The program...
Hi guys
Does anyone know what sort of modifications are required to set up the existing MQTT-SN example ( https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/samples...
i'm just beginning my bluetooth journey, and have some basic questions about sniffing/spoofing a BT remote control for an audio device (Topping DAC D50 iii)...
my goal:...
Hi Noridic team,
I have enabled Matter over Thread on the nRF5340. In this setup, I'm planning to reduce the TX power by setting CONFIG_OPENTHREAD_DEFAULT_TX_POWER=0. Apart...
Hi,
I have a question about FOTA jobs with queued and failed devices.
Let's say I am managing a group of 10 cellular devices (nRF9151) through the nRF Cloud UI. I create...
Good day,
I am currently working on a project involving the nRF54 series and would like to inquire about support for the NEC infrared (IR) communication protocol. Specifically...
I'm testing my code based on nrf5SDK v17.0.0 with nrf52832 board.
By nrf connect application,I can see the broadcast packet from my board.It looks something like this. ...
Hi I'm working with nrf5340 dk. I have a serial app (on windows) that is doing serial write continuously to the nrf5340 dk but it is not capturing all the data that I'm sending...
