I'm using the nRF9160 with the LIS2DH accelerometer and SDK version 2.5.2 . In my hardware setup, INT1 is connected to GPIO 0 and INT2 to GPIO 1 . I'm configuring both interrupt...
I have a custom hardware running on nrf52840 and using ncs 2.6.1. I have implemented a custom authentication flow with customer characteristic along with the BLE bonding....
Hi ,
I am developing an application which uses nrf52833. I want to perform OTA using 4g module(from Quectel). As per my understanding and explorations, there can be two...
Hello,
I'm using two nRF9161 to communicate with each other and I want to test and measure the differences between the 3 modes available in SDK3.0.0. First, I configured...
I have tested the nRF Cloud Multi Service Sample using Quick Start and it works perfectly.
I am trying to build the sample so that I can make small modifications for an...
Hi,
I am currently using 54L15-DK to create a radio test example, but there is a problem when I build the project: - sdk version: v2.9.0 - toolchain version: v2.9.1
...
Hello everyone,
We are developing products with nrf52840 and our default supply voltage is 1.8V.
Is it possible to program a custom 1.8V board with nRF52840DK?
We are...
Hi Nordic!
Long time short, I want to do an ANT application (S210, nRF51422) that pairs two slaves to one master. I have configured everything such that it pairs only when...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi Nordic,
We are trying to supply the chip nRF51422 with a Li-Ion battery. The nominal voltage is 3.7V, but as it is known, when full, this voltage can reach up to 4.2V...
Can the pc_ble_driver project located here be use in combination with SDK12?
We currently have it setup for SDK11 here, and want to upgrade to SDK12. We successfully built...
I want to develop a central role application (using a Redbear BLE Nano - based on nRF51)
I believe that this requires use of a softdevice and am looking for how to do this...
Hi. I am trying to set up timer in counter mode to count up signals from gpio through the ppi module, but it's not working. In main cycle I am testing the timer using led...
I want to sense bluetooth from any distance the radio can detect and without connecting, pairing or bonding. Simply turn led2 on while the nrf51822 senses RF and when it no...
For my application I need a lot of different timers. I dont use a soft device. Its a nRF52 Chip on board.
#define APP_TIMER_OP_QUEUE_SIZE 20
APP_TIMER_INIT(APP_TIMER_PRESCALER...
Experimental Buttonless DFU worked correctly when compiled with keil, but the same example compiled in eclipse by gcc is not switching to bootloader mode. value 0x01 is updated...
Hi There,
Are timers 3 & 4 accessible to the application when using the v3.0 S132 softstack on the NRF52?
Looking at table 4 of S132_SDS_v3.0.pdf they are not listed.
Cheers...
Hi Community, many thanks for reading!
I have built a Breadboardadapter for an ISP1302
Inside
On Breadboard
There is no Groundplane or design rules.
Yes,...
I am using a nrf8001 and the arduino aci library ported to work with my project.
I have started from hello world example.
Connecting to the device from android app, sending...
Hi there.
I am compiling the Nordic MQTT subscriber example (using TLS), and see the following error:
c:\program files (x86)\gnu tools arm embedded\5.4 2016q2\arm...
