Hi
I am using nRF52840 with SDK 15.3.
I have a project where I uses FatFS to write to a SD-card with SPI interface (SPIM3). This works very well.
I am now trying to...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with this specific exercise (l5_e2):
To ensure I wasn...
Hey so I just wanted to use the BMI270 on the Thingy:53 and Polling the acceleration values seems to be working just fine. I wanted to use the DATA_READY Trigger. I am working...
Hi everyone,
In nRF9160 with ncs 2.9.0 I've problems when trying publish a MQTT payload bigger than 2700 bytes aproximately. In advanced I already was adequated buffer size...
Hi, I've recently acquired an nRF54L15DK, and started the development on BLE, I'm fairly new to Nordic's enviroment. In the last couple days I've been trying to build the...
Hi everyone,
I use the ble-app-buttonless-dfu example to develop my application.
I make a mutual authentication to be sure the device is connected to the right mobile...
Hi everyone,
I'm developing a BLE application where I measure throughput between an nRF5340DK acting as peripheral and an nRF52 Dongle as the central (using a Python script...
I am intended to integrate the Nordic SoC nRF52832 in our PCB to generate a PWM.
However, I could not understand the difference between the following:
topicSchematic QFAA...
Hi to everyone, i have the mpu6050 code and i have to change it with parameters of adxl345.
i have this definitions:
#define ADDRESS_WHO_AM_I (0x75U) //!< WHO_AM_I register...
Hi, I am trying to connect a peripheral device which in this case is a BLE device called DELTA and I am trying to connect it to a central device which is the NRF52 board....
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
In nRF5_SDK_12.1.0_0d23e2a in file: ...\components\softdevice\common\softdevice_handler\ant_stack_handler_types.h In lines 30-32 inside #ifdef ANT_STACK_SUPPORT_REQD is preprocessor...
Hi ,
I have nRF51822 beacon and J-Link LITE and i am using nRFgo studio setup .I am trying to flash the hex file in to the beacon using nRfgo studio.The beacon has two...
Hello!
The DEC2 pin is connected to an N.C. capacitor C6 in the newest refreance layout and the nRF52 DK layout. So does it mean I can just left it DNC like the 44th pin...
Hi,
I have a custom board of nrf51822 with no external crystal, neither 16 Mhz nor 32Khz. I am trying to use uart and app timers from SDK11 but when I start any app timer...
I'm in a situation similar to the one described in this question:
devzone.nordicsemi.com/.../
The company performing the test ask me to provide a device that can switch...
I wanna execute rtc0 on the project which is inside examples\ble_peripheral\ble_app_uart file in sdk 11
When i write the following codes ,nrf51 is locked.bluetooth connection...
I created a characteristic of 20 byte length in a peripheral.
when peripheral does indication, the length of indication data in central is always 20 byte.
I want to send...
I'm porting from sdk10 to sdk12.1 and changing to .zip based libraries in keil5. I've unzipped the sdk into the directory and the examples work fine. However, if try to copy...
Please find attached the screenshot of the schematic where i have combined the RF circuitry from
the NRF52 DK and the NRF51822 dongle for a compact board development. . ...
Hello,
Can anyone tell me if it possible to have one peripheral device connected to 2 central devices ? I am using S132 softdevice with nRF52832 board.
Thank you !
nrf51connect.pcapng nrf52disconnect.pcapng Hi i m using pi3 with bluez and the gatttool i can easy connect to the Adafruit Feather M0 with a nrf51 as bluetooth module but...
