I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a custom board based on the nRF9160 and using nRF Connect SDK v3.0.2. We’ve developed the board in-house and integrated the npm1300 PMIC as part of...
Hello,
For our emission tests in an anechoic chamber we need to be sure that the BT antenna is up and running. Of course we cannot connect via BT from outside the chamber...
hi support team,
docs says we can program 54l15 external spi flash ,please refer to : https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-device/guides/programming_external_memory...
Hi all, I m new to Bluetooth Low Energy. I have to develop an indoor positioning project based on Bluetooth Low Energy 4.0 in which i have to locate person's current position...
My ble device try to notify a data to my android mobilephone after phone connect it,but sometimes,phone can't receive the data and error 8 occur .this happend frequently when...
Hi,
pstorage_raw_store() API fails as p_src address is not 4 byte aligned (i.e. 0x20002b1a), as p_src is RAM address and also as its "SOURCE" address is it necessary to...
Hey Folks
I wonder to design my own simple circuit based on NRF51422, the circuit should connect to a mobile app. By the way I'm I wonder to follow these steps:
visulaised...
Hi all,
I have one question about the deep sleep wakeup process in NRF24LE1. I want to realize the function that "when I press the button, it will cause rise edge on the...
Hi,
I'm testing doing a soft device update (v7.0 to v7.1) over DFU, but I consistently get OP_CODE_SYS_RESET sent to my device after 4 packets(80 bytes), at which point the...
Just want to know how acknowledged message works.
ANT document says there is no retry logic for acknowledged message.
According to ANT protocol, acknowledged message should...
Hi all!
I've been trying to OTA firmware using iOS nRF Toolbox App. I'm able to read.hex files in the App, although, after trying to send the file to the device the format...
I have a "heartbeat" LED which flashes for 10mS every 2 seconds. I was doing this with one of the HW timers and a PPI channel, but I have discovered that just having the HW...
How would I go about changing the connection event packet length?
I have an 8 byte characteristic setup with notifications enabled, but it still looks like it is transmitting...
Hi,
I have the following code with SD110 7.1.0:
static void uart_init(void) // device inter-communication
{
// Configure RX and TX pins.
nrf_gpio_pin_set(0);
nrf_gpio_cfg_output...
Hello,
I am building a sample protocol using nRF51822 DK. I am using S130 soft device. I have a few BLE nodes communicating with each other. The nRF51 DK acts as these nodes...
Is the nRF51822 pin-for-pin compatible with nRF51422?
I can't find any distributor stock of nRF51822-QFAC.
I see the eval kit has nRF51422. I don't need ANT functionality;...
Hii, i use nordic PCA10028 dev kit, to test the bluetooth of kit i simply load the ble_app_hrs example which is given in SDK, because of i don't know how softdevice 110 is...
